All Outputs (345)

Equivalent Slot Thermal Conductivity and Back-iron Extension Effects on Machine Cooling (2019)
Conference Proceeding

Back-iron Extension (BIE) is an effective thermal management technique which reduces the winding temperatures by projecting part of the back iron into the center of slot, thereby shortening the heat transfer path between the coil and back iron. Based... Read More about Equivalent Slot Thermal Conductivity and Back-iron Extension Effects on Machine Cooling.

Thermal Barrier for High-Voltage Permanent Magnet Synchronous Motor with Air-cooling Hybrid Ventilation Systems (2019)
Conference Proceeding

This paper addresses the thermal network improvement in a 315 kW high-voltage solid rotor permanent magnet synchronous motor, with a hybrid air-cooling system, by the proposed thermal barrier. The multi-coupled fields, as electromagnetic fields, flui... Read More about Thermal Barrier for High-Voltage Permanent Magnet Synchronous Motor with Air-cooling Hybrid Ventilation Systems.

A Novel Modelling Approach of Modular Multi Three-phase Drive System for High Performance Applications (2019)
Conference Proceeding

There is a growing attention in the industrial and academic sectors for the multi-phase drive for high power and high-speed applications. The multi three-phase drive with independent neutral points is a popular option for this application, as it allo... Read More about A Novel Modelling Approach of Modular Multi Three-phase Drive System for High Performance Applications.

Designing an Advanced Electrical Motor for Propulsion of Electric Aircraft (2019)
Conference Proceeding

A prototype motor rated for 500 kW 3,000 rpm has been developed for aircraft electric propulsion. The design of the motor was optimized using a coupled parameter problem of electromagnetic, mechanical and thermal performances. A high power density of... Read More about Designing an Advanced Electrical Motor for Propulsion of Electric Aircraft.

High-Speed Permanent Magnet Synchronous Motor Iron Loss Calculation Method Considering Multiphysics Factors (2019)
Journal Article

Comparative Analysis of AC losses with round magnet wire and Litz wire winding of a High – Speed PM Machine (2019)
Conference Proceeding

The growing trend of high speed, high power density machines for applications such as EVs, aerospace and machine tools demand these machines to work at higher electrical frequencies. Meanwhile, increasing the fundamental frequency leads to pronounced... Read More about Comparative Analysis of AC losses with round magnet wire and Litz wire winding of a High – Speed PM Machine.

Torque Ripple Reduction in Sectored Multi Three-Phase Machines Based on PWM Carrier Phase Shift (2019)
Journal Article

The interest in multiphase machines for high power and reliable drives has been growing, and many control algorithms have been proposed to improve their torque performance. This work presents a new approach to the modeling of a multi three-phase driv... Read More about Torque Ripple Reduction in Sectored Multi Three-Phase Machines Based on PWM Carrier Phase Shift.

Dual-Pulse Mode Control of a High-Speed Doubly Salient Electromagnetic Machine for Loss Reduction and Speed Range Extension (2019)
Journal Article

In this paper, a dual-pulse mode control of a high-speed doubly salient electromagnetic machine (DSEM) for efficiency improvement over a wide speed range is investigated and implemented. The dual-pulse mode control method and operation principle are... Read More about Dual-Pulse Mode Control of a High-Speed Doubly Salient Electromagnetic Machine for Loss Reduction and Speed Range Extension.

A SiC based 2-Level Power Converter for Shape-and-Space-Restricted Aerospace Applications (2019)
Conference Proceeding

Recent advancements in the power electronic device technologies, such as wide-band-gap devices including Silicon-Carbide (SiC) and Galium-Nitride (GaN), are acting as an enabling factor in development of compact power electronic systems. More specifi... Read More about A SiC based 2-Level Power Converter for Shape-and-Space-Restricted Aerospace Applications.

Internal Current Return Path for Ground Leakage Current Mitigation in Current Source Inverters (2019)
Journal Article

This paper analyzes in detail the effect of a simple solution for ground leakage current mitigation applicable to transformerless three-phase current source inverter (CSI). The circuit modification solution is assessed for both traditional CSI topolo... Read More about Internal Current Return Path for Ground Leakage Current Mitigation in Current Source Inverters.

Comparative study on two modular spoke-type PM machines for in-wheel traction applications (2019)
Journal Article

This paper focuses on the comparative analysis of modular spoke-type permanent magnet machines with two magnetization modes, which are referred to as M-I and M-II types. The analytical models of the proposed machines are built based on the simple mag... Read More about Comparative study on two modular spoke-type PM machines for in-wheel traction applications.

Challenges of the optimization of a high-speed induction machine for naval applications (2019)
Journal Article

In several industrial sectors, induction machines are being replaced with permanent magnet based alternatives, owing to the potential for higher power density and efficiency. However, high-speed applications feature a wide flux-weakening region, wher... Read More about Challenges of the optimization of a high-speed induction machine for naval applications.

Layered Al2O3-SiO2 and Al2O3-Ta2O5 thin-film composites for high dielectric strength, deposited by pulsed direct current and radio frequency magnetron sputtering (2019)
Journal Article

Multilayer thin films have the potential to act as high dielectric strength insulation for wire and microelectronics. In this study, films consisting of 2, 4 or 8 layers, composed of Al2O3 with SiO2 or Ta2O5, were prepared via pulsed direct current a... Read More about Layered Al2O3-SiO2 and Al2O3-Ta2O5 thin-film composites for high dielectric strength, deposited by pulsed direct current and radio frequency magnetron sputtering.

On the design of partial discharge-free low voltage electrical machines (2019)
Conference Proceeding

Modern electrical machines employed in transportation applications are required to provide high performance in terms of power (and torque) density. At the same time, being these applications safety-critical, a significant level of reliability and/or... Read More about On the design of partial discharge-free low voltage electrical machines.

Optimized Sizing of IPM Machines for Automotive Traction Application (2019)
Conference Proceeding

This paper presents the implementation of an electrical machine design tool including its overall architecture. The tool is flexible and can be employed for the sizing of any permanent magnet synchronous machine. The case study considered in this wor... Read More about Optimized Sizing of IPM Machines for Automotive Traction Application.

Information Technologies for Distributed Machine Drives: An Overview (2019)
Conference Proceeding

The exponential growth experienced by the semiconductor manufacturing field has led to a large proliferation of devices with large amounts computational power, enabling countless technologies and revolutionizing many fields. Control systems and machi... Read More about Information Technologies for Distributed Machine Drives: An Overview.

Dual-Rotor Permanent Magnet Motor for Electric Superbike (2019)
Conference Proceeding

The demand on high-performance electrical machines has significantly increased for aerospace and transportation industries in recent years. A racing electric motorbike is a suitable platform to validate and prove new concepts and machine topologies b... Read More about Dual-Rotor Permanent Magnet Motor for Electric Superbike.

Single-Phase Open-Circuit Fault Operation of Bearingless Multi-Sector PM Machines (2019)
Conference Proceeding

This paper investigates the single-phase open-circuit fault of a bearingless multi-sector PM synchronous machine. The mathematical model of the suspension force and torque generation is developed for both healthy and faulty conditions. The model is w... Read More about Single-Phase Open-Circuit Fault Operation of Bearingless Multi-Sector PM Machines.

Thermo-Mechanical Modelling of Bearing Chambers of a High-Speed Starter/Generator (2019)
Conference Proceeding

This paper describes the thermal-mechanical characterisation methodology for the bearing chambers of a high-speed (32,000 rpm) electrical starter/generator [1]; presenting a low cost analysis approach and design guideline for future machines. The met... Read More about Thermo-Mechanical Modelling of Bearing Chambers of a High-Speed Starter/Generator.

Torque Ripple Investigation in Squirrel Cage Induction Machines (2019)
Conference Proceeding

Low torque ripple of electrical machines is an important requirement for many different applications. The causes of torque fluctuations in squirrel cage asynchronous induction motors might be a challenging task due to the complex phenomena raised by... Read More about Torque Ripple Investigation in Squirrel Cage Induction Machines.