Skip to main content

Research Repository

Advanced Search

Outputs (14)

The potential of exploiting non-symmetric structures in electrical machines (2019)
Presentation / Conference Contribution
Nuzzo, S., Marfoli, A., Papini, L., Bolognesi, P., Gerada, C., & Galea, M. (2019, October). The potential of exploiting non-symmetric structures in electrical machines. Presented at 45th Annual Conference of the IEEE Industrial Electronics Society (IECON 2019), Lisbon, Portugal

Typically, electrical machines feature rotor and stator winding configurations and core structures which comply with both simplicity and cost requirements. Such constraints limit the design search space and degrees of freedom, thus leading to exploit... Read More about The potential of exploiting non-symmetric structures in electrical machines.

Enhancing the Torque Density of Conventional PM-SynRel Machine with Hybrid Flux Barrier (2019)
Presentation / Conference Contribution
Kumar, R. M. R., Vakil, G., Gerada, D., Walker, A., La Rocca, S., Al-Ani, M., Gerada, C., Paciura, K., McQueen, A., & Fernandes, B. G. (2019, October). Enhancing the Torque Density of Conventional PM-SynRel Machine with Hybrid Flux Barrier. Presented at 45th Annual Conference of the IEEE Industrial Electronics Society (IECON 2019), Lisbon, Portugal

Electrical machines with high torque density are required for traction application. Availability of bonded magnets with complex shapes and magnetization pattern can significantly extend the design space of electrical machines. This paper introduces a... Read More about Enhancing the Torque Density of Conventional PM-SynRel Machine with Hybrid Flux Barrier.

High Power High Speed PM-Assisted SynRel Machines with Ferrite and Rare Earth Magnets for Future Electric Commercial Vehicles (2019)
Presentation / Conference Contribution
Kumar, R. M. R., Zou, T., La Rocca, A., Vakil, G., Gerada, D., Walker, A., Gerada, C., Paciura, K., McQueen, A., & Fernandes, B. G. (2019, October). High Power High Speed PM-Assisted SynRel Machines with Ferrite and Rare Earth Magnets for Future Electric Commercial Vehicles. Presented at 45th Annual Conference of the IEEE Industrial Electronics Society (IECON 2019), Lisbon, Portugal

High power density and high torque density are the fundamental requirements for electric machines used in traction application. The former is obtained by potentially increasing the speed of the machine while the latter by using high energy density ra... Read More about High Power High Speed PM-Assisted SynRel Machines with Ferrite and Rare Earth Magnets for Future Electric Commercial Vehicles.

Trade-off Study of a High Power Density Starter-Generator for Turboprop Aircraft System (2019)
Presentation / Conference Contribution
Khowja, M. R., Vakil, G., Gerada, C., Yang, T., Bozhko, S., & Wheeler, P. (2019, October). Trade-off Study of a High Power Density Starter-Generator for Turboprop Aircraft System. Presented at 45th Annual Conference of the IEEE Industrial Electronics Society (IECON 2019), Lisbon, Portugal

Mechanically-driven actuators, compressors and pumps are being replaced by the aircraft manufacturers that shift the trend towards 'More Electric Aircraft' and hence reducing the mechanical linkages within the aircraft system. This elevates the depen... Read More about Trade-off Study of a High Power Density Starter-Generator for Turboprop Aircraft System.

Numerical study of the impact of different cooling arrangements on a high length/diameter ratio motor for electric commercial vehicle (2019)
Presentation / Conference Contribution
La Rocca, S., La Rocca, A., Walker, A., Vakil, G., Gerada, D., Al-Ani, M., Zou, T., Ramanathan, R., Gerada, C., McQueen, A., & Paciura, K. (2019, October). Numerical study of the impact of different cooling arrangements on a high length/diameter ratio motor for electric commercial vehicle. Presented at International Conference on Electrotechnical Complexes and Systems (ICOECS 2019), Ufa, Russia

Computational Fluid Dynamics (CFD) was used to carry out a fluid flow and thermal investigation of a high power dense traction machine for electric commercial vehicle. One of the features of the machine design considered is the high Length/Diameter (... Read More about Numerical study of the impact of different cooling arrangements on a high length/diameter ratio motor for electric commercial vehicle.

Optimized Carrier Disposition Based Discontinuous Pulse-width Modulation Method for three-level NPC Converters (2019)
Presentation / Conference Contribution
Wang, M., Xu, L., Yang, B., Li, J., Gu, C., Zhang, H., Gerada, C., & Li, Y. (2019, September). Optimized Carrier Disposition Based Discontinuous Pulse-width Modulation Method for three-level NPC Converters. Presented at IEEE Energy Conversion Congress and Exposition (ECCE 2019 ), Baltimore, MD, USA

Three level neutral-point-clamped (3L-NPC) converter is a multilevel topology that is well-suited solution in high voltage, high frequency applications such as flexible AC transmission systems and electric vehicle drive systems. This paper is focused... Read More about Optimized Carrier Disposition Based Discontinuous Pulse-width Modulation Method for three-level NPC Converters.

Rotor UMP & Mechanical Response in HSPMSM in Typical Running Conditions (2019)
Presentation / Conference Contribution
He, Y.-L., Vakil, G., Zhang, X.-C., Gao, P., Gerada, D., & Gerada, C. (2019, September). Rotor UMP & Mechanical Response in HSPMSM in Typical Running Conditions. Presented at 2019 IEEE Energy Conversion Congress and Exposition, ECCE 2019, Baltimore, MD, USA

This paper presents a comprehensive analysis on the rotor unbalanced magnetic pull (UMP) and the consequent mechanical response in 6 typical running conditions in a 20000 rpm high speed permanent magnet synchronous motor (HSPMSM) through finite eleme... Read More about Rotor UMP & Mechanical Response in HSPMSM in Typical Running Conditions.

A Novel Modelling Approach of Modular Multi Three-phase Drive System for High Performance Applications (2019)
Presentation / Conference Contribution
Wang, X., Gu, C., Buticchi, G., Zhang, H., & Gerada, C. (2019, August). A Novel Modelling Approach of Modular Multi Three-phase Drive System for High Performance Applications. Presented at 2019 22nd International Conference on Electrical Machines and Systems (ICEMS), Harbin, China

There is a growing attention in the industrial and academic sectors for the multi-phase drive for high power and high-speed applications. The multi three-phase drive with independent neutral points is a popular option for this application, as it allo... Read More about A Novel Modelling Approach of Modular Multi Three-phase Drive System for High Performance Applications.

Comparative Analysis of AC losses with round magnet wire and Litz wire winding of a High – Speed PM Machine (2019)
Presentation / Conference Contribution
Bardalai, A., Zhang, X., Zou, T., Gerada, D., Li, J., & Gerada, C. (2019, August). Comparative Analysis of AC losses with round magnet wire and Litz wire winding of a High – Speed PM Machine. Presented at 2019 22nd International Conference on Electrical Machines and Systems (ICEMS), Harbin, China

The growing trend of high speed, high power density machines for applications such as EVs, aerospace and machine tools demand these machines to work at higher electrical frequencies. Meanwhile, increasing the fundamental frequency leads to pronounced... Read More about Comparative Analysis of AC losses with round magnet wire and Litz wire winding of a High – Speed PM Machine.