All Outputs (9)

Performance improvement of simplified synchronous generators using an active power filter (2017)
Presentation / Conference Contribution
Abu-Jalala, A.-H., Cox, T., Gerada, C., & Rashed, M. (2017). Performance improvement of simplified synchronous generators using an active power filter.

Active power filters (APF) are used to improve power quality and are commonly connected in parallel with the load at the point of common coupling (PCC). They are used to compensate for harmonics from nonlinear loads, for reactive power compensation a... Read More about Performance improvement of simplified synchronous generators using an active power filter.

A two degrees of freedom system for wheel traction applications (2017)
Journal Article
Roggia, S., Cupertino, F., Gerada, C., & Galea, M. (2018). A two degrees of freedom system for wheel traction applications. IEEE Transactions on Industrial Electronics, 65(6), 4483-4491. https://doi.org/10.1109/TIE.2017.2767554

In this paper, the use of conical induction machines is proposed for an in-wheel traction application. Such machines offer a rotational movement combined with a translational motion of the rotor. The horizontal movement is essential when active engag... Read More about A two degrees of freedom system for wheel traction applications.

Axial position estimation of conical shaped motors for aerospace traction applications (2017)
Journal Article
Roggia, S., Cupertino, F., Gerada, C., & Galea, M. (2017). Axial position estimation of conical shaped motors for aerospace traction applications. IEEE Transactions on Industry Applications, 53(6), 5405-5414. https://doi.org/10.1109/TIA.2017.2717911

This paper is concerned with the use of conical induction machines. Such machines are extremely valuable when apart from the rotational torque output, an axial translation of the rotor is also required. The inherent attraction between the stator and... Read More about Axial position estimation of conical shaped motors for aerospace traction applications.

Enhancing electromagnetic launch capability: design of a small launch system for large UAVs (2017)
Presentation / Conference Contribution
Cox, T., Yang, T., & Gerada, C. (2017). Enhancing electromagnetic launch capability: design of a small launch system for large UAVs.

Unmanned Aerial Vehicles (UAVs) play a critical and increasing role in modern combat, giving significantly enhanced surveillance, communication and strike capabilities. There are currently a large range of UAV’s available, but in general the more cap... Read More about Enhancing electromagnetic launch capability: design of a small launch system for large UAVs.

Power Loss and Thermal Analysis of a MW High-Speed Permanent Magnet Synchronous Machine (2017)
Journal Article
Zhang, Y., McLoone, S., Cao, W., Qiu, F., & Gerada, C. (2017). Power Loss and Thermal Analysis of a MW High-Speed Permanent Magnet Synchronous Machine. IEEE Transactions on Energy Conversion, 32(4), 1468-1478. https://doi.org/10.1109/TEC.2017.2710159

© 1986-2012 IEEE. High-speed permanent magnet synchronous machines (PMSMs) have attracted much attention due to their high power density, high efficiency, and compact size for direct-drive applications. However, the consequent power loss density is h... Read More about Power Loss and Thermal Analysis of a MW High-Speed Permanent Magnet Synchronous Machine.

A fractional slot multiphase air-core compulsator with concentrated winding (2017)
Journal Article
Zhao, W., Wu, S., Cui, S., Gerada, C., Zhang, H., & Xu, Z. (2017). A fractional slot multiphase air-core compulsator with concentrated winding. IEEE Transactions on Plasma Science, 45(7), 1387-1393. https://doi.org/10.1109/TPS.2017.2705243

Compulsator is a specially designed generator capa¬ble of delivering high current pulses to a low-impedance load, such as the electromagnetic railgun. In order to increase the tip speed of the rotor, advanced composite materials have been used in the... Read More about A fractional slot multiphase air-core compulsator with concentrated winding.

Design optimization of integrated rotational inductor for high-speed AC drive applications (2017)
Presentation / Conference Contribution
Khowja, M. R., Gerada, C., Vakil, G., Patel, C., & Wheeler, P. (2017). Design optimization of integrated rotational inductor for high-speed AC drive applications.

In order to make an efficient and power dense overall system, a close physical and functional integration of passive components is required instead of having a separate sub¬system for passives. Such power dense system is vital in aerospace and marine... Read More about Design optimization of integrated rotational inductor for high-speed AC drive applications.

Self-excitation and energy recovery of air-core compulsators (2017)
Journal Article
Zhao, W., Wu, S., Cui, S., Gerada, C., Zhang, H., & Xu, Z. (2017). Self-excitation and energy recovery of air-core compulsators. IEEE Transactions on Plasma Science, 45(7), 1168-1174. https://doi.org/10.1109/TPS.2017.2700027

As power supplies, compulsators are popular choices for high-end railgun power supplies. In order to increase power and energy density, air-core compulsators are proposed by using composite materials instead of traditional iron-core compulsators. Due... Read More about Self-excitation and energy recovery of air-core compulsators.

Controlling DC permeability in cast steels (2017)
Journal Article
Sumner, A., Gerada, C., Brown, N., & Clare, A. (2017). Controlling DC permeability in cast steels. Journal of Magnetism and Magnetic Materials, 429, 79-85. https://doi.org/10.1016/j.jmmm.2016.12.137

Annealing (at multiple cooling rates) and quenching (with tempering) was performed on specimens of cast steel of varying composition. The aim was to devise a method for selecting the steel with the highest permeability, from any given range of steels... Read More about Controlling DC permeability in cast steels.