All Outputs (161)

High speed drives review: machines, converters and applications (2016)
Conference Proceeding
Abebe, R., Di Nardo, M., Gerada, D., Lo Calzo, G., Papini, L., & Gerada, C. (2016). High speed drives review: machines, converters and applications.

The development of new power electronic device and high performance magnetic materials are the main technological factors that have led both industries and research community to focus their attention on high speed electrical drives. Several papers ha... Read More about High speed drives review: machines, converters and applications.

Trade-off analysis and design of a high power density PM machine for flooded industrial pump (2016)
Conference Proceeding
Al-Timimy, A., Degano, M., Xu, Z., Lo Calzo, G., Giangrande, P., Galea, M., …Zhang, H. (2016). Trade-off analysis and design of a high power density PM machine for flooded industrial pump.

This paper presents the trade-off analysis and design of a high power-density machine for industrial pump applications. The developed permanent magnet synchronous machine drives an electric, oil flooded pump. Different slot/pole combination and windi... Read More about Trade-off analysis and design of a high power density PM machine for flooded industrial pump.

2-D analytical model for dual-stator machines with permanent magnets (2016)
Conference Proceeding
Golovanov, D., Galea, M., & Gerada, C. (2016). 2-D analytical model for dual-stator machines with permanent magnets.

This paper proposes an analytical model that considers the torque characteristics and results in an optimum geometry for dual-stator synchronous machines with permanent magnets. The distribution of the magnetic field in the air gap is obtained by sol... Read More about 2-D analytical model for dual-stator machines with permanent magnets.

Stator and rotor vent modelling in a MVA rated synchronous machine (2016)
Conference Proceeding
Connor, P. H., Eastwick, C., Pickering, S. J., Gerada, C., & Rolston, R. (2016). Stator and rotor vent modelling in a MVA rated synchronous machine. In 2016 XXII International Conference on Electrical Machines (ICEM) (571-577). https://doi.org/10.1109/ICELMACH.2016.7732583

An investigation into the solution dependence of a conjugate heat transfer computational fluid dynamics (CFD) model of a synchronous generator, with respect to meshing, has been carried out. Utilising CFD as a tool for investigating the airflow and t... Read More about Stator and rotor vent modelling in a MVA rated synchronous machine.

Short term duty electrical machines (2016)
Conference Proceeding
Arumugam, P., & Gerada, C. (2016). Short term duty electrical machines.

This paper presents a design of a short term duty electrical machine working in an extreme environment consisting of 80oC ambient temperature and altitudes of over 30,000m. Higher power density is a key factor in the design wherein the machine’s oper... Read More about Short term duty electrical machines.

Structural design optimization of a high speed synchronous reluctance machine (2016)
Conference Proceeding
Di Nardo, M., Lo Calzo, G., Galea, M., & Gerada, C. (2016). Structural design optimization of a high speed synchronous reluctance machine.

Synchronous reluctance machines, including the permanent magnet assisted variants are competitive motor topologies if the application requires high efficiency and a cost effective solution with a high flux weakening capability. However, increasing sp... Read More about Structural design optimization of a high speed synchronous reluctance machine.

Distributed current control for multi-three phase synchronous machines in fault conditions (2016)
Conference Proceeding
Galassini, A., Costabeber, A., Degano, M., Gerada, C., Tessarolo, A., & Castellan, S. (2016). Distributed current control for multi-three phase synchronous machines in fault conditions.

Among challenges and requirements of on-going electrification process and future transportation systems there is demand for arrangements with both increased fault tolerance and reliability. Next aerospace, power-train and automotive systems exploitin... Read More about Distributed current control for multi-three phase synchronous machines in fault conditions.

Thermal management of a permanent magnet motor for an directly coupled pump (2016)
Conference Proceeding
Xu, Z., Al-Timimy, A., Degano, M., Giangrande, P., Lo Calzo, G., Zhang, H., …Gerada, C. (2016). Thermal management of a permanent magnet motor for an directly coupled pump.

A high speed permanent magnet motor is designed for a flooded industrial pump. Oil in the pump is used to cool the motor. Due to the limitation of space and mass requirement for the application, thermal management is one of the main challenges. This... Read More about Thermal management of a permanent magnet motor for an directly coupled pump.

Design and optimization of a high power density machine for flooded industrial pump (2016)
Conference Proceeding
Al-Timimy, A., Degano, M., Giangrande, P., Lo Calzo, G., Xu, Z., Galea, M., …Xia, L. (2016). Design and optimization of a high power density machine for flooded industrial pump.

This paper presents the design optimization procedure of a high power-density, permanent magnet synchronous machine for industrial pump applications. The designed machine drives an electric, oil flooded pump. In order to achieve higher torque-density... Read More about Design and optimization of a high power density machine for flooded industrial pump.

Radial force control of multi-sector permanent magnet machines (2016)
Conference Proceeding
Valente, G., Papini, L., Formentini, A., Gerada, C., & Zanchetta, P. (2016). Radial force control of multi-sector permanent magnet machines.

The paper presents an alternative radial force control technique for a Multi-Sector Permanent Magnet machine (MSPM). Radial force control has been widely investigated for a variety of bearingless machines and can be also applied to conventional PMSM... Read More about Radial force control of multi-sector permanent magnet machines.

The importance of considering pushback time and arrivals when routing departures on the ground at airports (2016)
Conference Proceeding
Stergianos, C., Atkin, J., Schittekat, P., Nordlander, T. E., Gerada, C., & Morvan, H. (in press). The importance of considering pushback time and arrivals when routing departures on the ground at airports.

With the constant increase in air traffic, airports are facing capacity problems. Many airports are increasingly interested in utilising optimisation methods for specific airport processes. However, many such processes do happen in parallel, and maxi... Read More about The importance of considering pushback time and arrivals when routing departures on the ground at airports.

Damper cage loss reduction and no-load voltage THD improvements in salient-pole synchronous generators (2016)
Conference Proceeding
Nuzzo, S., Galea, M., Gerada, C., Gerada, D., Mebarki, A., & Brown, N. (2016). Damper cage loss reduction and no-load voltage THD improvements in salient-pole synchronous generators.

Salient-pole synchronous generators (SG) have a long history of utilization as reliable power generation systems. Important aspects of such generators include a high power-to-weight ratio, high efficiency and a low cost per kVA output [1]. Another cr... Read More about Damper cage loss reduction and no-load voltage THD improvements in salient-pole synchronous generators.

Estimating current derivatives for sensorless motor drive applications (2015)
Conference Proceeding
Hind, D. M., Sumner, M., & Gerada, C. (2015). Estimating current derivatives for sensorless motor drive applications.

The PWM current derivative technique for sensorless control of AC machines requires current derivative measurements under certain PWM vectors. This is often not possible under narrow PWM vectors due to high frequency (HF) oscillations which affect th... Read More about Estimating current derivatives for sensorless motor drive applications.

Development of an aircraft wheel actuator for green taxiing (2014)
Conference Proceeding
Galea, M., Pickering, S. J., Tighe, C., XU, Z., Hamiti, T., & Gerada, C. (2014). Development of an aircraft wheel actuator for green taxiing. doi:10.1109/ICELMACH.2014.6960537

In this paper, the design and construction aspects of a wheel actuator to be used for aircraft taxiing on the ground and which will be located in the main landing gear are addressed. The main challenges with the application are the high torque densit... Read More about Development of an aircraft wheel actuator for green taxiing.

Mechanical and thermal management design of a motor for an aircraft wheel actuator (2014)
Conference Proceeding
Xu, Z., Galea, M., Tighe, C., Hamiti, T., Gerada, C., & Pickering, S. (2015). Mechanical and thermal management design of a motor for an aircraft wheel actuator. In 2014 17th International Conference on Electrical Machines and Systems (ICEMS). https://doi.org/10.1109/ICEMS.2014.7014056

A permanent magnet motor is designed as an actuator for taxiing large aircraft in an airport. The motor is attached to the main aircraft wheel to provide a direct drive. A special topology for this machine is developed selected and designed. Due to a... Read More about Mechanical and thermal management design of a motor for an aircraft wheel actuator.

Implementation of a multi-level Power Electronic Inverter library in Modelica (2014)
Conference Proceeding
Hill, C., Giangrande, P., Gerada, C., & Bozhko, S. (in press). Implementation of a multi-level Power Electronic Inverter library in Modelica.

This paper presents a newly developed Power Electronic Inverter library in Modelica. The library utilises a multi-level approach with increasing model complexity at progressively higher levels. All levels are fully interchangeable so as to provide a... Read More about Implementation of a multi-level Power Electronic Inverter library in Modelica.

CFD modelling of an entire synchronous generator for improved thermal management (2012)
Conference Proceeding
Connor, P. H., Pickering, S. J., Gerada, C., Eastwick, C. N., & Micallef, C. (2012). CFD modelling of an entire synchronous generator for improved thermal management. . https://doi.org/10.1049/cp.2012.0290

This paper is the first in a series dedicated to investigating the airflow and thermal management of electrical machines. Due to the temperature dependent resistive losses in the machine's windings any improvement in cooling provides a direct reducti... Read More about CFD modelling of an entire synchronous generator for improved thermal management.

An analytical and genetic-algorithm-based design tool for brushless excitation systems of low-medium rated synchronous generators
Conference Proceeding
Nuzzo, S., Galea, M., Gerada, C., & Brown, N. (in press). An analytical and genetic-algorithm-based design tool for brushless excitation systems of low-medium rated synchronous generators.

The sizing procedures adopted for the everyday design of electrical machines are well known and consolidated. However, for brushless exciters of field wound, synchronous generators, there is significant room for improvement as the impact of the diode... Read More about An analytical and genetic-algorithm-based design tool for brushless excitation systems of low-medium rated synchronous generators.

Prediction of the voltage drop due to the diode commutation process in the excitation system of salient-pole synchronous generators
Conference Proceeding
Nuzzo, S., Galea, M., Gerada, C., & Brown, N. (in press). Prediction of the voltage drop due to the diode commutation process in the excitation system of salient-pole synchronous generators.

The commutation processes in uncontrolled diode rectifiers have been extensively studied and modelled. However, in some applications, such as electrical power generation, the effects of these processes are often neglected. In low to medium rated, fie... Read More about Prediction of the voltage drop due to the diode commutation process in the excitation system of salient-pole synchronous generators.

Integrated output filter inductor for permanent magnet motor drives
Conference Proceeding
Raza Khowja, M., Gerada, C., Vakil, G., Wheeler, P., & Patel, C. (in press). Integrated output filter inductor for permanent magnet motor drives.

This paper presents a novel approach to integrate the output filter inductor in permanent magnet synchronous motor (PMSM) drive system. The integrated output filter inductor is based on utilizing the motor magnetics as a filter inductance instead of... Read More about Integrated output filter inductor for permanent magnet motor drives.