Outputs (40)

Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting (2024)
Journal Article
Laolu-Balogun, E., Owen, S., Read, S., Shipway, P., & Voisey, K. (2024). Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting. Wear, 552-553, Article 205426. https://doi.org/10.1016/j.wear.2024.205426

Investigations into effects of humidity and oxygen on a polymer-bonded MoS2-based dry film lubricant (DFL) coating, on grit-blasted Ti-6Al-4V using a cylinder-on-flat configuration, are reported. Sustained low friction and low wear occurred in both l... Read More about Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting.

The evolution of subsurface deformation and tribological degradation of a multiphase Fe-based hardfacing induced by sliding contact (2023)
Journal Article
Carrington, M., Daure, J., Utada, S., Ratia-Hanby, V., Shipway, P., Stewart, D., & McCartney, D. (2024). The evolution of subsurface deformation and tribological degradation of a multiphase Fe-based hardfacing induced by sliding contact. Materials Science and Engineering: A, 892, Article 146023. https://doi.org/10.1016/j.msea.2023.146023

Multiphase Fe-based hardfacing alloys, for example Tristelle 5183 Fe-21%Cr-10%Ni-7.5%Nb-5%Si-2%C in wt.%, are extensively used for tribological applications, including valves, bearings and drive mechanisms, where two surfaces are unavoidably subjecte... Read More about The evolution of subsurface deformation and tribological degradation of a multiphase Fe-based hardfacing induced by sliding contact.

Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited (2023)
Journal Article
Laolu-Balogun, E., Owen, S., Booth, T., Pattinson, G., Shipway, P., & Voisey, K. (2023). Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited. Tribology International, 188, Article 108863. https://doi.org/10.1016/j.triboint.2023.108863

The superior fretting performance of polymer-bonded MoS2-based dry film lubricant (DFL) coating on a plasma-sprayed Cu-Ni-In under-layer is well known. The Cu-Ni-In under-layer changes both the material and the topography of the sur... Read More about Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited.

Galling of stainless steels as a function of test conditions in an ASTM G196-type test setup – The role of temperature, rotational velocity, interrupted rotation and rotational distance (2023)
Journal Article
Daure, J. L., Kóti, D., Carrington, M. J., McCartney, D. G., Stewart, D. A., & Shipway, P. H. (2023). Galling of stainless steels as a function of test conditions in an ASTM G196-type test setup – The role of temperature, rotational velocity, interrupted rotation and rotational distance. Wear, 524-525, Article 204804. https://doi.org/10.1016/j.wear.2023.204804

Austenitic stainless steels have attractive properties for use in corrosive environments, but their use in components where motion under load is experienced (such as valves) is limited by their poor galling behaviour. Whilst stainless steels with imp... Read More about Galling of stainless steels as a function of test conditions in an ASTM G196-type test setup – The role of temperature, rotational velocity, interrupted rotation and rotational distance.

Debris expulsion as a rate determining process in fretting – The effect of slip amplitude on debris expulsion behaviour and rates (2023)
Journal Article
Zhu, T., Bennett, C. J., & Shipway, P. H. (2023). Debris expulsion as a rate determining process in fretting – The effect of slip amplitude on debris expulsion behaviour and rates. Wear, 523, Article 204818. https://doi.org/10.1016/j.wear.2023.204818

In contrast to the well-established understanding of sliding wear, recent work has clearly demonstrated that the instantaneous wear rate in fretting of metals is dependent upon the contact size due to the fact that transport of species in and out of... Read More about Debris expulsion as a rate determining process in fretting – The effect of slip amplitude on debris expulsion behaviour and rates.

Microstructure formation in the powder HIPed hardfacing alloy Tristelle 5183 (Fe-21%Cr-10%Ni-7.5%Nb-5%Si-2%C in wt%) (2021)
Journal Article
Carrington, M. J., McCartney, D. G., Shipway, P. H., & Stewart, D. A. (2022). Microstructure formation in the powder HIPed hardfacing alloy Tristelle 5183 (Fe-21%Cr-10%Ni-7.5%Nb-5%Si-2%C in wt%). Materials Characterization, 184, Article 111688. https://doi.org/10.1016/j.matchar.2021.111688

Tristelle 5183 (Fe-21%Cr-10%Ni-7%Nb-5%Si-2%C in wt%) is an alternative material to cobalt-based alloys for wear resistant hardfacing applications. In this work, gas atomised powder was consolidated by hot isostatic pressing (HIPing) at 1120 ± 10 oC w... Read More about Microstructure formation in the powder HIPed hardfacing alloy Tristelle 5183 (Fe-21%Cr-10%Ni-7.5%Nb-5%Si-2%C in wt%).

Corrigendum to ‘Understanding and modelling wear rates and mechanisms in fretting via the concept of rate-determining processes - Contact oxygenation, debris formation and debris ejection’ (Wear (2021) 486–487, (S004316482100452X), (10.1016/j.wear.2021.204066)) (2021)
Journal Article
Shipway, P. H., Kirk, A. M., Bennett, C. J., & Zhu, T. (2022). Corrigendum to ‘Understanding and modelling wear rates and mechanisms in fretting via the concept of rate-determining processes - Contact oxygenation, debris formation and debris ejection’ (Wear (2021) 486–487, (S004316482100452X), (10.1016/j.wear.2021.204066)). Wear, 488-489, Article 204161. https://doi.org/10.1016/j.wear.2021.204161

Understanding and modelling wear rates and mechanisms in fretting via the concept of rate-determining processes - Contact oxygenation, debris formation and debris ejection (2021)
Journal Article
Shipway, P. H., Kirk, A. M., Bennett, C. J., & Zhu, T. (2021). Understanding and modelling wear rates and mechanisms in fretting via the concept of rate-determining processes - Contact oxygenation, debris formation and debris ejection. Wear, 486-487, Article 204066. https://doi.org/10.1016/j.wear.2021.204066

A new framework which describes the role of three key processes in fretting wear of metals is proposed, with these three processes being: (i) oxygen transport into the contact; (ii) formation of oxide-based wear debris in the contact and (iii) ejecti... Read More about Understanding and modelling wear rates and mechanisms in fretting via the concept of rate-determining processes - Contact oxygenation, debris formation and debris ejection.

Interaction of displacement amplitude and frequency effects in fretting wear of a high strength steel: Impact on debris bed formation and subsurface damage (2021)
Journal Article
Kirk, A. M., Sun, W., Bennett, C. J., & Shipway, P. H. (2021). Interaction of displacement amplitude and frequency effects in fretting wear of a high strength steel: Impact on debris bed formation and subsurface damage. Wear, 482-483, Article 203981. https://doi.org/10.1016/j.wear.2021.203981

In previous work, fretting frequency has been observed to have a significant impact not only on wear rates, but also on the nature of fretting debris and the development of subsurface damage; however, while the “frequency effect” has been shown in so... Read More about Interaction of displacement amplitude and frequency effects in fretting wear of a high strength steel: Impact on debris bed formation and subsurface damage.

Time-dependence and exposure-dependence of material removal rates in fretting (2021)
Journal Article
Shipway, P. H. (2021). Time-dependence and exposure-dependence of material removal rates in fretting. Wear, 477, Article 203826. https://doi.org/10.1016/j.wear.2021.203826

Fretting generally results in either material removal or fatigue, or a combination of both. Although the term is rarely used now, in the early literature addressing this subject, fretting that resulted in material removal was sometimes termed “fretti... Read More about Time-dependence and exposure-dependence of material removal rates in fretting.