Outputs (45)

A water-soluble core material for manufacturing hollow composite sections (2017)
Journal Article
Xiao, Z., Harper, L., Kennedy, A. R., & Warrior, N. (2017). A water-soluble core material for manufacturing hollow composite sections. Composite Structures, 182, https://doi.org/10.1016/j.compstruct.2017.09.058

This paper presents the development of a low-cost water-soluble core material, which is suitable for producing hollow composite structures via high pressure moulding processes, such as compression moulding and resin transfer moulding. The bulk materi... Read More about A water-soluble core material for manufacturing hollow composite sections.

Double diaphragm forming simulation for complex composite structures (2017)
Journal Article
Chen, S., McGregor, O., Endruweit, A., Elsmore, M., De Focatiis, D., Harper, L., & Warrior, N. (2017). Double diaphragm forming simulation for complex composite structures. Composites Part A: Applied Science and Manufacturing, 95, 346-358. https://doi.org/10.1016/j.compositesa.2017.01.017

A finite element (FE) model has been developed to simulate the double diaphragm forming (DDF) process, to identify potential defects when forming complex 3D preforms from 2D biaxial non-crimp fabric plies. Three different metrics have been introduced... Read More about Double diaphragm forming simulation for complex composite structures.

Compression moulding of composites with hybrid fibre architectures (2016)
Journal Article
Corbridge, D., Harper, L. T., De Focatiis, D. S., & Warrior, N. (2017). Compression moulding of composites with hybrid fibre architectures. Composites Part A: Applied Science and Manufacturing, 95, 87-99. https://doi.org/10.1016/j.compositesa.2016.12.018

Advanced Sheet Moulding Compounds (ASMC) and unidirectional (UD) prepregs have been co-compression moulded to form a hybrid composite material. In-mould flow influences the UD fibre architecture in two ways. When UD fibres are aligned transversely to... Read More about Compression moulding of composites with hybrid fibre architectures.

3D geometric modelling of discontinuous fibre composites using a force-directed algorithm (2016)
Journal Article
Harper, L., Qian, C., Luchoo, R., & Warrior, N. (2017). 3D geometric modelling of discontinuous fibre composites using a force-directed algorithm. Journal of Composite Materials, 51(17), 2389-2406. https://doi.org/10.1177/0021998316672722

A geometrical modelling scheme is presented to produce representative architectures for discontinuous fibre composites, enabling downstream modelling of mechanical properties. The model generates realistic random fibre architectures containing high f... Read More about 3D geometric modelling of discontinuous fibre composites using a force-directed algorithm.

Defect formation during preforming of a bi-axial non-crimp fabric with a pillar stitch pattern (2016)
Journal Article
Chen, S., McGregor, O., Harper, L., Endruweit, A., & Warrior, N. (2016). Defect formation during preforming of a bi-axial non-crimp fabric with a pillar stitch pattern. Composites Part A: Applied Science and Manufacturing, 91, 156-167. https://doi.org/10.1016/j.compositesa.2016.09.016

To capture the asymmetrical shear behaviour of a bi-axial NCF with a pillar stitch, a non-orthogonal constitutive model was developed and implemented in finite element forming simulations. Preforming experiments indicate that the local distribution o... Read More about Defect formation during preforming of a bi-axial non-crimp fabric with a pillar stitch pattern.

Flow characteristics of carbon fibre moulding compounds (2016)
Journal Article
Evans, A., Qian, C., Turner, T., Harper, L., & Warrior, N. (2016). Flow characteristics of carbon fibre moulding compounds. Composites Part A: Applied Science and Manufacturing, 90, 1-12. https://doi.org/10.1016/j.compositesa.2016.06.020

This paper presents the development of a low-cost carbon fibre moulding compound using an automated spray deposition process. Directed Fibre Compounding (DFC) is used to produce charge packs directly from low cost carbon fibre tows and liquid epoxy r... Read More about Flow characteristics of carbon fibre moulding compounds.

Optimisation of composite bone plates for ulnar transverse fractures (2016)
Journal Article
Chakladar, N. D., Harper, L. T., & Parsons, A. J. (2016). Optimisation of composite bone plates for ulnar transverse fractures. Journal of the Mechanical Behavior of Biomedical Materials, 57, https://doi.org/10.1016/j.jmbbm.2016.01.029

Metallic bone plates are commonly used for arm bone fractures where conservative treatment (casts) cannot provide adequate support and compression at the fracture site. These plates, made of stainless steel or titanium alloys, tend to shield stress t... Read More about Optimisation of composite bone plates for ulnar transverse fractures.

Flow characteristics of carbon fibre sheet moulding compounds (2015)
Presentation / Conference Contribution
Evans, A. D., Qian, C. C., Harper, L. T., Warrior, N. A., Brookbank, P., & Savage, L. (2015, July). Flow characteristics of carbon fibre sheet moulding compounds. Presented at 20th ICCM International Conferences on Composite Materials, Copenhagen, Denmark

© 2015 International Committee on Composite Materials. All rights reserved. This paper presents the development of a low cost carbon fibre moulding compound using a robotic spray deposition process, developed at the University of Nottingham. Directed... Read More about Flow characteristics of carbon fibre sheet moulding compounds.

A study of an improved cutting mechanism of composite materials using novel design of diamond micro-core drills (2014)
Journal Article
Butler-Smith, P. W., Axinte, D. A., Daine, M., Kennedy, A. R., Harper, L. T., Bucourt, J. F., & Ragueneau, R. (2015). A study of an improved cutting mechanism of composite materials using novel design of diamond micro-core drills. International Journal of Machine Tools and Manufacture, 88, 175-183. https://doi.org/10.1016/j.ijmachtools.2014.10.002

Core drilling at small diameters in carbon composite materials is largely carried out using diamond electroplated tools consisting of hollow shafts and simplistic geometries that are likely to work in an abrasional/rubbing mode for material removal.... Read More about A study of an improved cutting mechanism of composite materials using novel design of diamond micro-core drills.

Mechanical, degradation and cytocompatibility properties of magnesium coated phosphate glass fibre reinforced polycaprolactone composites (2014)
Journal Article
Liu, X., Hasan, M. S., Grant, D. M., Harper, L. T., Parsons, A. J., Palmer, G., Rudd, C. D., & Ahmed, I. (2014). Mechanical, degradation and cytocompatibility properties of magnesium coated phosphate glass fibre reinforced polycaprolactone composites. Journal of Biomaterials Applications, 29(5), https://doi.org/10.1177/0885328214541302

Retention of mechanical properties of phosphate glass fibre reinforced degradable polyesters such as polycaprolactone and polylactic acid in aqueous media has been shown to be strongly influenced by the integrity of the fibre/polymer interface. A pre... Read More about Mechanical, degradation and cytocompatibility properties of magnesium coated phosphate glass fibre reinforced polycaprolactone composites.