All Outputs (49)

The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment (2016)
Journal Article
Aboulkhair, N. T., Maskery, I., Tuck, C., Ashcroft, I., & Everitt, N. M. (2016). The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment. Materials Science and Engineering: A, 667, 139-146. https://doi.org/10.1016/j.msea.2016.04.092

Selective laser melting (SLM) of aluminium is of research interest because of its potential benefits to high value manufacturing applications in the aerospace and automotive industries. In order to demonstrate the credibility of SLM Al parts, their m... Read More about The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment.

An investigation into reinforced and functionally graded lattice structures (2016)
Journal Article
Maskery, I., Hussey, A., Panesar, A., Aremu, A., Tuck, C., Ashcroft, I., & Hague, R. J. (in press). An investigation into reinforced and functionally graded lattice structures. Journal of Cellular Plastics, https://doi.org/10.1177/0021955X16639035

Lattice structures are regarded as excellent candidates for use in lightweight energy absorbing applications, such as crash protection. In this paper we investigate the crushing behaviour, mechanical properties and energy absorption of lattices made... Read More about An investigation into reinforced and functionally graded lattice structures.

Nanoindentation shows uniform local mechanical properties across melt pools and layers produced by selective laser melting of AlSi10Mg alloy (2016)
Journal Article
Everitt, N. M., Aboulkhair, N. T., Maskery, I., Tuck, C., & Ashcroft, I. (2016). Nanoindentation shows uniform local mechanical properties across melt pools and layers produced by selective laser melting of AlSi10Mg alloy. https://doi.org/10.5185/amlett.2016.6171

Single track and single layer AlSi10Mg has been produced by selective laser melting (SLM) of alloy powder on a AlSi12 cast substrate. The SLM technique produced a cellular-dendritic ultra-fined grained microstructure. Chemical composition mapping an... Read More about Nanoindentation shows uniform local mechanical properties across melt pools and layers produced by selective laser melting of AlSi10Mg alloy.

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography (2016)
Journal Article
Maskery, I., Aboulkhair, N., Corfield, M., Tuck, C., Clare, A., Leach, R. K., …Hague, R. J. (2016). Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography. Materials Characterization, 111, https://doi.org/10.1016/j.matchar.2015.12.001

We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The spe... Read More about Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography.

On the formation of AlSi10Mg single tracks and layers in selective laser melting: Microstructure and nano-mechanical properties (2015)
Journal Article
Aboulkhair, N. T., Maskery, I., Tuck, C., Ashcroft, I., & Everitt, N. M. (2016). On the formation of AlSi10Mg single tracks and layers in selective laser melting: Microstructure and nano-mechanical properties. Journal of Materials Processing Technology, 230, 88-98. https://doi.org/10.1016/j.jmatprotec.2015.11.016

Selective laser melting (SLM) is a relatively new manufacturing technique that can be used to process a range of materials. Aluminum alloys are potential candidates for SLM but are more difficult to process than the titanium alloys more commonly used... Read More about On the formation of AlSi10Mg single tracks and layers in selective laser melting: Microstructure and nano-mechanical properties.

On the Precipitation Hardening of Selective Laser Melted AlSi10Mg (2015)
Journal Article
Tuck, C., Aboulkhair, N. T., Tuck, C., Ashcroft, I., Maskery, I., & Everitt, N. M. (2015). On the Precipitation Hardening of Selective Laser Melted AlSi10Mg. Metallurgical and Materials Transactions A, 46(8), 3337-3341. https://doi.org/10.1007/s11661-015-2980-7

Precipitation hardening of selective laser melted AlSi10Mg was investigated in terms of solution heat treatment and aging duration. The influence on the microstructure and hardness was established, as was the effect on the size and density of Si part... Read More about On the Precipitation Hardening of Selective Laser Melted AlSi10Mg.

Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size (2015)
Journal Article
Maskery, I., Aremu, A., Simonelli, M., Tuck, C., Wildman, R., Ashcroft, I., & Hague, R. (2015). Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size. Experimental Mechanics, 55(7), 1261-1272. https://doi.org/10.1007/s11340-015-0021-5

Significant weight savings in parts can be made through the use of additive manufacture (AM), a process which enables the construction of more complex geometries, such as functionally graded lattices, than can be achieved conventionally. The existing... Read More about Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size.

A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V (2015)
Journal Article
Hague, R., Tuck, C., Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., …Hague, R. J. (2015). A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V. Metallurgical and Materials Transactions A, 46(9), 3842-3851. https://doi.org/10.1007/s11661-015-2882-8

The creation of an object by selective laser melting (SLM) occurs by melting contiguous areas of a powder bed according to a corresponding digital model. It is therefore clear that the success of this metal Additive Manufacturing (AM) technology reli... Read More about A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V.

Nano-hardness and microstructure of selective laser melted AlSi10Mg scan tracks (2015)
Presentation / Conference Contribution
Aboulkhair, N. T., Tuck, C., Maskery, I., Ashcroft, I., & Everitt, N. (2015). Nano-hardness and microstructure of selective laser melted AlSi10Mg scan tracks. In Industrial Laser Applications Symposium (ILAS 2015). https://doi.org/10.1117/12.2190015

Selective laser melting (SLM) of aluminium alloys faces more challenges than other ongoing alloys such as stainless steels and titanium alloys because of the material’s properties. It is important to study single scan tracks if high density large par... Read More about Nano-hardness and microstructure of selective laser melted AlSi10Mg scan tracks.