Skip to main content

Research Repository

Advanced Search

Outputs (46)

The Engineer’s Guide to Materials: An Applications-Focused Introduction to Materials Science (2024)
Book
Voisey, K. T. (2024). The Engineer’s Guide to Materials: An Applications-Focused Introduction to Materials Science. Springer. https://doi.org/10.1007/978-3-031-62937-2

Why do engineers need to know about materials? Metals, polymers, ceramics, composites — what are the key characteristics of each class of material and which is best suited for a given industrial application? How can service conditions change the perf... Read More about The Engineer’s Guide to Materials: An Applications-Focused Introduction to Materials Science.

Laser cutting of CFRP using novel cutting strategies (2024)
Journal Article
Kelsey, D., Elkington, H., Jackson-Crisp, A., Harper, L., Marithmu, S., & Voisey, K. (2024). Laser cutting of CFRP using novel cutting strategies. Procedia CIRP, 124, 509-512. https://doi.org/10.1016/j.procir.2024.08.163


Laser cutting of carbon fibre reinforced plastics generates a heat affected zone (HAZ) in the vicinity of the cut, affecting the integrity of the material and therefore the uptake of laser cutting for composite applications. This w... Read More about Laser cutting of CFRP using novel cutting strategies.

Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting (2024)
Journal Article
Laolu-Balogun, E., Owen, S., Read, S., Shipway, P., & Voisey, K. (2024). Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting. Wear, 552-553, Article 205426. https://doi.org/10.1016/j.wear.2024.205426

Investigations into effects of humidity and oxygen on a polymer-bonded MoS2-based dry film lubricant (DFL) coating, on grit-blasted Ti-6Al-4V using a cylinder-on-flat configuration, are reported. Sustained low friction and low wear occurred in both l... Read More about Effect of humidity and oxygen on friction, wear and durability of a polymer-bonded molybdenum disulfide (MoS2)-based dry film lubricant (DFL) coating system in large amplitude fretting.

Laser cladding: A high-speed-imaging examination of powder catchment efficiency as a function of the melt pool geometry and its position under the powder stream (2023)
Journal Article
Koti, D., Powell, J., Naesstroem, H., Spaccapaniccia, C., & Voisey, K. T. (2023). Laser cladding: A high-speed-imaging examination of powder catchment efficiency as a function of the melt pool geometry and its position under the powder stream. Journal of Laser Applications, 35(4), Article 042065. https://doi.org/10.2351/7.0001199

This paper provides quantitative information about the paths taken by blown powder particles during laser cladding. A proportion of the powder is "wasted" by bouncing off the solid areas surrounding the melt pool. This wastage reduces the productivit... Read More about Laser cladding: A high-speed-imaging examination of powder catchment efficiency as a function of the melt pool geometry and its position under the powder stream.

Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited (2023)
Journal Article
Laolu-Balogun, E., Owen, S., Booth, T., Pattinson, G., Shipway, P., & Voisey, K. (2023). Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited. Tribology International, 188, Article 108863. https://doi.org/10.1016/j.triboint.2023.108863

The superior fretting performance of polymer-bonded MoS2-based dry film lubricant (DFL) coating on a plasma-sprayed Cu-Ni-In under-layer is well known. The Cu-Ni-In under-layer changes both the material and the topography of the sur... Read More about Lifetime of MoS2 based DFL systems in fretting with and without a Cu-Ni-In under-layer: the dependence on the topography of the surface onto which the DFL is deposited.

Powder catchment efficiency in laser cladding (directed energy deposition). An investigation into standard laser cladding and the ABA cladding technique (2023)
Journal Article
Koti, D., Powell, J., Naesstroem, H., & Voisey, K. T. (2023). Powder catchment efficiency in laser cladding (directed energy deposition). An investigation into standard laser cladding and the ABA cladding technique. Journal of Laser Applications, 35, Article 012025. https://doi.org/10.2351/7.0000904

This paper investigates the efficiency of powder catchment in blown powder laser cladding (a directed energy deposition technique). A comparison is made between standard “track by overlapping track” cladding (“AAA” cladding) and “ABA” cladding, where... Read More about Powder catchment efficiency in laser cladding (directed energy deposition). An investigation into standard laser cladding and the ABA cladding technique.

Assessing the quality and productivity of laser cladding and direct energy deposition: Guidelines for researchers (2023)
Journal Article
Powell, J., Koti, D., Garmendia, X., & Voisey, K. T. (2023). Assessing the quality and productivity of laser cladding and direct energy deposition: Guidelines for researchers. Journal of Laser Applications, 35(1), Article 012024. https://doi.org/10.2351/7.0000897

This paper provides guidelines and advice to researchers and engineers in the field of laser cladding and related direct energy deposition techniques to help establish a standardized approach to quality assessment and productivity metrics. Factors co... Read More about Assessing the quality and productivity of laser cladding and direct energy deposition: Guidelines for researchers.

Improving laser cladding productivity with ‘ABA’ cladding (2022)
Presentation / Conference Contribution
Koti, D., Powell, J., & Voisey, K. (2022, September). Improving laser cladding productivity with ‘ABA’ cladding. Presented at 12th CIRP Conference on Photonic Technologies [LANE 2022], Fürth, Germany

Laser Cladding is one of several processes within Additive Manufacturing and usually involves the production of a clad surface by adding parallel, overlapping lines of clad material to the surface of a substrate. In this work a new laser cladding tec... Read More about Improving laser cladding productivity with ‘ABA’ cladding.

Image processing algorithm to determine an optimised 2D laser cutting trajectory (2019)
Presentation / Conference Contribution
Syam, W. P., Bansal, R., Benardos, P., Britchford, E., Hopkinson, A., Voisey, K., & Branson, D. T. (2019, September). Image processing algorithm to determine an optimised 2D laser cutting trajectory. Presented at 25th IEEE International Conference on Automation & Computing (ICAC'19), Lancaster, UK

Laser cutting processes offer high-quality and fast cutting capability across a wide variety of materials, including metals, plastics and organic tissues. To enable 2D laser cutting process, a set of (x, y) Cartesian coordinates that form a cutting t... Read More about Image processing algorithm to determine an optimised 2D laser cutting trajectory.