Outputs (330)

In-process tool wear prediction system based on machine learning techniques and force analysis (2018)
Journal Article
Gouarir, A., Martínez-Arellano, G., Terrazas, G., Benardos, P., & Ratchev, S. (2018). In-process tool wear prediction system based on machine learning techniques and force analysis. Procedia CIRP, 77, 501-504. https://doi.org/10.1016/j.procir.2018.08.253

This paper presents an in-process tool wear prediction system, which uses a force sensor to monitor the progression of the tool flank wear and machine learning (ML), more specifically, a Convolutional Neural Network (CNN) as a method to predict tool... Read More about In-process tool wear prediction system based on machine learning techniques and force analysis.

Alternative-fuel station network design under impact of station failures (2018)
Journal Article
Tran, T. H., & Nguyen, T. B. T. (2019). Alternative-fuel station network design under impact of station failures. Annals of Operations Research, 279(1-2), 151-186. https://doi.org/10.1007/s10479-018-3054-1

In this paper, we have formulated a mixed-integer non-linear programming model for alternative-fuel station location problem in which each station can fail with a site-specific probability. The model aims to maximise the total expected traffic volume... Read More about Alternative-fuel station network design under impact of station failures.

GNSS trajectory anomaly detection using similarity comparison methods for pedestrian navigation (2018)
Journal Article
Peltola, P., Xiao, J., Moore, T., Jiménez, A., & Seco, F. (2018). GNSS trajectory anomaly detection using similarity comparison methods for pedestrian navigation. Sensors, 18(9), Article 3165. https://doi.org/10.3390/s18093165

The urban setting is a challenging environment for GNSS receivers. Multipath and other anomalies typically increase the positioning error of the receiver. Moreover, the error estimate of the position is often unreliable. In this study, we detect GNSS... Read More about GNSS trajectory anomaly detection using similarity comparison methods for pedestrian navigation.

Solar-powered Stirling engine: past, present, and future (2018)
Presentation / Conference Contribution
Hafez, A., Khodary, A., & Hamed, A. (2018, September). Solar-powered Stirling engine: past, present, and future. Presented at 5th International Conference on Power and Energy Systems Engineering (CPESE 2018), Nagoya University, Nagoya, Japan

Investigation of Housing Preferences in View of the Housing Market Dynamics in Doha Metropolitan (2018)
Book Chapter
Ibrahim, H., Salama, A., Wiedmann, F., Awwaad, R., & Aboukalloub, B. (2018). Investigation of Housing Preferences in View of the Housing Market Dynamics in Doha Metropolitan. In M. Awang, & M. Isa (Eds.), The Advances in Civil Engineering Materials. ICACE 2018 (1-10). Springer Singapore. https://doi.org/10.1007/978-981-13-2511-3_1

© Springer Nature Singapore Pte Ltd. 2019. Since the 2000s, Doha has gone through enormous economic growth and urbanization processes. The massive migration inflows have suggested particular housing preferences that are driven by the demographic and... Read More about Investigation of Housing Preferences in View of the Housing Market Dynamics in Doha Metropolitan.

Experimental investigation of the effect of magnetic field on vapour absorption rate of LiBr+H2O nanofluid (2018)
Presentation / Conference Contribution
Wu, S., & Rincon Ortiz, C. (2018, September). Experimental investigation of the effect of magnetic field on vapour absorption rate of LiBr+H2O nanofluid. Presented at Heat Powered Cycles Conference 2018

This paper reports an experimental study on the vapour absorption process with an aqueous lithium bromide solution based nanofluid. It is a comparison study to investigate the effect of the nanofluid (base fluid + nanopowders) and the nanofluid under... Read More about Experimental investigation of the effect of magnetic field on vapour absorption rate of LiBr+H2O nanofluid.

Combining continuous flow oscillatory baffled reactors and microwave heating: Process intensification and accelerated synthesis of metal-organic frameworks (2018)
Journal Article
Laybourn, A., López-Fernández, A. M., Thomas-Hillman, I., Katrib, J., Lewis, W., Dodds, C., Harvey, A. P., & Kingman, S. W. (2019). Combining continuous flow oscillatory baffled reactors and microwave heating: Process intensification and accelerated synthesis of metal-organic frameworks. Chemical Engineering Journal, 356, 170-177. https://doi.org/10.1016/j.cej.2018.09.011

We have constructed a continuous flow oscillatory baffled reactor (CF-OBR) equipped with a homogeneous and controllable microwave applicator in an entirely novel design. This affords a new route to chemical production incorporating many of the princi... Read More about Combining continuous flow oscillatory baffled reactors and microwave heating: Process intensification and accelerated synthesis of metal-organic frameworks.

Surface defects repairing of sprayed Ca-P coating by the microwave-hydrothermal method (2018)
Journal Article
Su, Y., Li, K., Hou, X., & He, S. (2018). Surface defects repairing of sprayed Ca-P coating by the microwave-hydrothermal method. Ceramics International, 44(17), 21699-21709. https://doi.org/10.1016/j.ceramint.2018.08.258

The increasing interest in decreasing the surface defects of sprayed Ca-P coating deposited on carbon/carbon (C/C) composites to enhance the bonding strength, bioactivity and corrosion resistance of the coating is justified by the growing evidence of... Read More about Surface defects repairing of sprayed Ca-P coating by the microwave-hydrothermal method.

Development of three-dimensional printing polymer-ceramic scaffolds with enhanced compressive properties and tuneable resorption (2018)
Journal Article
Zhou, Z., Cunningham, E., Lennon, A., McCarthy, H. O., Buchanan, F., & Dunne, N. (2018). Development of three-dimensional printing polymer-ceramic scaffolds with enhanced compressive properties and tuneable resorption. Materials Science and Engineering: C, 93, 975-986. https://doi.org/10.1016/j.msec.2018.08.048

In this study, bone tissue engineered scaffolds fabricated via powder-based 3D printing from hydroxyapatite (HA) and calcium sulphate (CaSO4) powders were investigated. The combination of using a fast resorbing CaSO4 based powder and the relatively s... Read More about Development of three-dimensional printing polymer-ceramic scaffolds with enhanced compressive properties and tuneable resorption.

A technology platform for monitoring homes within a community energy scheme: design and implementation challenges (2018)
Presentation / Conference Contribution
Shipman, R., & Gillott, M. (2018, August). A technology platform for monitoring homes within a community energy scheme: design and implementation challenges. Presented at The 17th International Conference on Sustainable Energy Technologies (SET 2018)

This paper describes a technology platform for monitoring homes within a community energy scheme. A range of sensors were deployed to measure in-home environmental conditions, occupancy, electrical power, electrical energy, thermal energy, heating be... Read More about A technology platform for monitoring homes within a community energy scheme: design and implementation challenges.