All Outputs (26)

Environmental Impacts of Selective Laser Melting: Do Printer, Powder, Or Power Dominate? (2016)
Journal Article
Faludi, J., Baumers, M., Maskery, I., & Hague, R. (2017). Environmental Impacts of Selective Laser Melting: Do Printer, Powder, Or Power Dominate?. Journal of Industrial Ecology, 21(S1), S144-S156. https://doi.org/10.1111/jiec.12528

© 2016 The Authors. Journal of Industrial Ecology, published by Wiley Periodicals, Inc., on behalf of Yale University. This life cycle assessment measured environmental impacts of selective laser melting, to determine where most impacts arise: machin... Read More about Environmental Impacts of Selective Laser Melting: Do Printer, Powder, Or Power Dominate?.

X-ray computed tomography for additive manufacturing: a review (2016)
Journal Article
Thompson, A., Maskery, I., & Leach, R. K. (2016). X-ray computed tomography for additive manufacturing: a review. Measurement Science and Technology, 27(7), Article 072001. https://doi.org/10.1088/0957-0233/27/7/072001

In this review, the use of x-ray computed tomography (XCT) is examined, identifying the requirement for volumetric dimensional measurements in industrial verification of additively manufactured (AM) parts. The XCT technology and AM processes are summ... Read More about X-ray computed tomography for additive manufacturing: a review.

An investigation into reinforced and functionally graded lattice structures (2016)
Journal Article
Maskery, I., Hussey, A., Panesar, A., Aremu, A., Tuck, C., Ashcroft, I., & Hague, R. J. (in press). An investigation into reinforced and functionally graded lattice structures. Journal of Cellular Plastics, https://doi.org/10.1177/0021955X16639035

Lattice structures are regarded as excellent candidates for use in lightweight energy absorbing applications, such as crash protection. In this paper we investigate the crushing behaviour, mechanical properties and energy absorption of lattices made... Read More about An investigation into reinforced and functionally graded lattice structures.

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography (2016)
Journal Article
Maskery, I., Aboulkhair, N., Corfield, M., Tuck, C., Clare, A., Leach, R. K., …Hague, R. J. (2016). Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography. Materials Characterization, 111, https://doi.org/10.1016/j.matchar.2015.12.001

We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The spe... Read More about Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography.

Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size (2015)
Journal Article
Maskery, I., Aremu, A., Simonelli, M., Tuck, C., Wildman, R., Ashcroft, I., & Hague, R. (2015). Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size. Experimental Mechanics, 55(7), 1261-1272. https://doi.org/10.1007/s11340-015-0021-5

Significant weight savings in parts can be made through the use of additive manufacture (AM), a process which enables the construction of more complex geometries, such as functionally graded lattices, than can be achieved conventionally. The existing... Read More about Mechanical Properties of Ti-6Al-4V Selectively Laser Melted Parts with Body-Centred-Cubic Lattices of Varying cell size.

A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V (2015)
Journal Article
Hague, R., Tuck, C., Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., …Hague, R. J. (2015). A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V. Metallurgical and Materials Transactions A, 46(9), 3842-3851. https://doi.org/10.1007/s11661-015-2882-8

The creation of an object by selective laser melting (SLM) occurs by melting contiguous areas of a powder bed according to a corresponding digital model. It is therefore clear that the success of this metal Additive Manufacturing (AM) technology reli... Read More about A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V.