All Outputs (49)

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography (2016)
Journal Article
Maskery, I., Aboulkhair, N., Corfield, M., Tuck, C., Clare, A., Leach, R. K., …Hague, R. J. (2016). Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography. Materials Characterization, 111, https://doi.org/10.1016/j.matchar.2015.12.001

We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The spe... Read More about Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography.

An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials (2015)
Journal Article
Chen, X., Ashcroft, I., Wildman, R. D., & Tuck, C. (2015). An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 471(2183), Article 20150477. https://doi.org/10.1098/rspa.2015.0477

A method using experimental nanoindentation and inverse finite-element analysis (FEA) has been developed that enables the spatial variation of material constitutive properties to be accurately determined. The method was used to measure property varia... Read More about An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials.

Toward better build volume packing in additive manufacturing: classification of existing problems and benchmarks (2015)
Presentation / Conference Contribution
Araujo, L., Özcan, E., Atkin, J., Baumers, M., Tuck, C., & Hague, R. J. (2015). Toward better build volume packing in additive manufacturing: classification of existing problems and benchmarks.

In many cases, the efficient operation of Additive Manufacturing (AM) technology relies on build volumes being packed effectively. Packing algorithms have been developed in response to this requirement. The configuration of AM build volumes is partic... Read More about Toward better build volume packing in additive manufacturing: classification of existing problems and benchmarks.

A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V (2015)
Journal Article
Hague, R., Tuck, C., Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., …Hague, R. J. (2015). A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V. Metallurgical and Materials Transactions A, 46(9), 3842-3851. https://doi.org/10.1007/s11661-015-2882-8

The creation of an object by selective laser melting (SLM) occurs by melting contiguous areas of a powder bed according to a corresponding digital model. It is therefore clear that the success of this metal Additive Manufacturing (AM) technology reli... Read More about A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V.

Aging behavior of thermoplastic elastomers in the laser sintering process (2014)
Journal Article
Ziegelmeier, S., Wöllecke, F., Tuck, C. J., Goodridge, R. D., & Hague, R. J. (2014). Aging behavior of thermoplastic elastomers in the laser sintering process. Journal of Materials Research, 29(17), 1841-1851. https://doi.org/10.1557/jmr.2014.172

It is known that polymers used in laser sintering (LS) change their intrinsic properties due to processing conditions that are close to the crystalline melting temperature. This paper evaluates the aging behavior of a thermoplastic polyurethane powde... Read More about Aging behavior of thermoplastic elastomers in the laser sintering process.

Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V (2014)
Journal Article
Simonelli, M., Tse, Y., & Tuck, C. (2014). Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V. Materials Science and Engineering: A, 616, https://doi.org/10.1016/j.msea.2014.07.086

Recent research on the additive manufacturing (AM) of Ti alloys has shown that the mechanical properties of the parts are affected by the characteristic microstructure that originates from the AM process. To understand the effect of the microstructur... Read More about Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V.

An experimental study into the effects of bulk and flow behaviour of laser sintering polymer powders on resulting part properties (2014)
Journal Article
Ziegelmeier, S., Christou, P., Wöllecke, F., Tuck, C., Goodridge, R. D., Hague, R. J., …Wintermantel, E. (2015). An experimental study into the effects of bulk and flow behaviour of laser sintering polymer powders on resulting part properties. Journal of Materials Processing Technology, 215, https://doi.org/10.1016/j.jmatprotec.2014.07.029

The properties of parts manufactured by laser sintering (LS) are, amongst others, influenced by the packing and flow efficiencies of the powders being processed. In particular, this study investigated the influence of the bulk and flow characteris... Read More about An experimental study into the effects of bulk and flow behaviour of laser sintering polymer powders on resulting part properties.

The formation of α + β microstructure in as-fabricated selective laser melting of Ti–6Al–4V (2014)
Journal Article
Simonelli, M., Tse, Y. Y., & Tuck, C. (2014). The formation of α + β microstructure in as-fabricated selective laser melting of Ti–6Al–4V. Journal of Materials Research, 29(17), 2028-2035. https://doi.org/10.1557/jmr.2014.166

Ti-6Al-4V parts made by the additive manufacturing (AM) technique selective laser melting (SLM) generally show poor ductility due to their fine martensitic microstructure. This study was designed to assess whether a more suitable microstructure can b... Read More about The formation of α + β microstructure in as-fabricated selective laser melting of Ti–6Al–4V.

On the texture formation of selective laser melted Ti-6Al-4V (2014)
Journal Article
Simonelli, M., Tse, Y. Y., & Tuck, C. (2014). On the texture formation of selective laser melted Ti-6Al-4V. Metallurgical and Materials Transactions A, 45(6), https://doi.org/10.1007/s11661-014-2218-0

Selective laser melting (SLM) has been shown to be an attractive manufacturing route for the production of α/β titanium alloys. The relationship between the SLM process parameters and the microstructure of titanium alloys has been the object of sever... Read More about On the texture formation of selective laser melted Ti-6Al-4V.