Skip to main content

Research Repository

Advanced Search

All Outputs (44)

Selective recrystallization of cellulose composite powders and microstructure creation through 3D binder jetting (2018)
Journal Article
Holland, S., Tuck, C., & Foster, T. (2018). Selective recrystallization of cellulose composite powders and microstructure creation through 3D binder jetting. Carbohydrate Polymers, 200, 229-238. https://doi.org/10.1016/j.carbpol.2018.07.064

Binder jetting is an additive manufacturing technique in which powdered material is sequentially laid down and printed on by an ink binder, in a selective manner, to form a 3D object. Unfortunately work in this area relevant to food materials is larg... Read More about Selective recrystallization of cellulose composite powders and microstructure creation through 3D binder jetting.

Band gap behavior of optimal one-dimensional composite structures with an additive manufactured stiffener (2018)
Journal Article
Ampatzidis, T., Leach, R. K., Tuck, C., & Chronopoulos, D. (2018). Band gap behavior of optimal one-dimensional composite structures with an additive manufactured stiffener. Composites Part B: Engineering, 153, https://doi.org/10.1016/j.compositesb.2018.07.012

In this work, the banded behaviour of composite one-dimensional structures with an additive manufactured stiffener is examined. A finite element method is used to calculate the stiffness, mass and damping matrices, and periodic structure theory is us... Read More about Band gap behavior of optimal one-dimensional composite structures with an additive manufactured stiffener.

Scanning photocurrent microscopy of 3D printed light trapping structures in dye-sensitized solar cells (2018)
Journal Article
Knott, A. N., Makarovsky, O., O’Shea, P., Tuck, C., & Wu, Y. (2018). Scanning photocurrent microscopy of 3D printed light trapping structures in dye-sensitized solar cells. Solar Energy Materials and Solar Cells, 180, https://doi.org/10.1016/j.solmat.2018.02.028

Converting solar energy directly into electricity as a clean and renewable energy resource is immensely important to solving the energy crisis and environmental pollution problems induced by the consumption of fossil fuels. Dye-sensitized solar cells... Read More about Scanning photocurrent microscopy of 3D printed light trapping structures in dye-sensitized solar cells.

Fluid gels: a new feedstock for high viscosity jetting (2018)
Journal Article
Holland, S., Tuck, C., & Foster, T. (2018). Fluid gels: a new feedstock for high viscosity jetting. Food Biophysics, 13(2), https://doi.org/10.1007/s11483-018-9523-x

Suspensions of gel particles which are pourable or spoonable at room temperature can be created by shearing a gelling biopolymer through its gelation (thermal or ion mediated) rather than allowing quiescent cooling – thus the term ‘fluid gel’ may be... Read More about Fluid gels: a new feedstock for high viscosity jetting.

Creep behaviour of inconel 718 processed by laser powder bed fusion (2018)
Journal Article
Xu, Z., Hyde, C., Tuck, C., & Clare, A. (2018). Creep behaviour of inconel 718 processed by laser powder bed fusion. Journal of Materials Processing Technology, 256, https://doi.org/10.1016/j.jmatprotec.2018.01.040

Additive manufacturing lends itself well to the manufacture of aerospace parts due to the high complexity and small volume of many components found in modern aero engines. By exploiting additive manufacturing design freedoms, enhanced part functional... Read More about Creep behaviour of inconel 718 processed by laser powder bed fusion.

3D reactive inkjet printing of polydimethylsiloxane (2017)
Journal Article
Sturgess, C., Tuck, C. J., Ashcroft, I. A., & Wildman, R. D. (2017). 3D reactive inkjet printing of polydimethylsiloxane. Journal of Materials Chemistry C, 5(37), 9733-9745. https://doi.org/10.1039/c7tc02412f

© 2017 The Royal Society of Chemistry. Material jetting is a process whereby liquid material can be deposited onto a substrate to solidify. Through a process of progressive additional layers, this deposition can then be used to produce 3D structures.... Read More about 3D reactive inkjet printing of polydimethylsiloxane.

Valorisation of lignin by depolymerisation and fractionation using supercritical fluids and conventional solvents (2017)
Journal Article
Perez, E., Tuck, C. O., & Poliakoff, M. (in press). Valorisation of lignin by depolymerisation and fractionation using supercritical fluids and conventional solvents. Journal of Supercritical Fluids, https://doi.org/10.1016/j.supflu.2017.07.033

A procedure for Lignosulphonate valorisation is investigated. An attempt has been made to obtain diverse value-added products maximizing the atom economy. This procedure is carried in sequential steps starting with an oxidative depolymerization in su... Read More about Valorisation of lignin by depolymerisation and fractionation using supercritical fluids and conventional solvents.

Staged thermomechanical testing of nickel superalloys produced by selective laser melting (2017)
Journal Article
Xu, Z., Hyde, C. J., Thompson, A., Leach, R. K., Maskery, I., Tuck, C., & Clare, A. T. (2017). Staged thermomechanical testing of nickel superalloys produced by selective laser melting. Materials and Design, 133, 520-527. https://doi.org/10.1016/j.matdes.2017.08.009

The creep performance of additively manufactured components remains an issue before additive manufacturing can be put fully implemented. In this study, Inconel 718 two-bar specimens are produced by selective laser melting and subjected to a ‘staged’... Read More about Staged thermomechanical testing of nickel superalloys produced by selective laser melting.

Calorimetric study and microstructure analysis of the order-disorder phase transformation in silicon steel built by SLM (2017)
Journal Article
Lemke, J., Simonelli, M., Garibaldi, M., Ashcroft, I., Hague, R., Vedani, M., …Tuck, C. (2017). Calorimetric study and microstructure analysis of the order-disorder phase transformation in silicon steel built by SLM. Journal of Alloys and Compounds, 722, 293-301. https://doi.org/10.1016/j.jallcom.2017.06.085

Innovative Additive Manufacturing (AM) technologies like Selective Laser Melting (SLM) could prove to be efficient for the processing of brittle silicon steel (Fe-Si) with high silicon content. This research elucidates the effects of heat-treatment o... Read More about Calorimetric study and microstructure analysis of the order-disorder phase transformation in silicon steel built by SLM.

A novel approach to design lesion-specific stents for minimum recoil (2016)
Journal Article
Farhan Khan, M., Brackett, D., Ashcroft, I., Tuck, C., & Wildman, R. D. (in press). A novel approach to design lesion-specific stents for minimum recoil. Journal of Medical Devices, 11(1), Article 011001. https://doi.org/10.1115/1.4034880

Stent geometries are obtained by topology optimization for minimized compliance under different stenosis levels and plaque material types. Three levels of stenosis by cross-sectional area, i.e., 30%, 40%, and 50% and three different plaque material p... Read More about A novel approach to design lesion-specific stents for minimum recoil.

A combined inverse finite element – elastoplastic modelling method to simulate the size-effect in nanoindentation and characterise materials from the nano to micro-scale (2016)
Journal Article
Chen, X., Ashcroft, I., Wildman, R. D., & Tuck, C. (2017). A combined inverse finite element – elastoplastic modelling method to simulate the size-effect in nanoindentation and characterise materials from the nano to micro-scale. International Journal of Solids and Structures, 104-105, 25-34. https://doi.org/10.1016/j.ijsolstr.2016.11.004

Material properties such as hardness can be dependent on the size of the indentation load when that load is small, a phenomenon known as the indentation size effect (ISE). In this work an inverse finite element method (IFEM) is used to investigate th... Read More about A combined inverse finite element – elastoplastic modelling method to simulate the size-effect in nanoindentation and characterise materials from the nano to micro-scale.

A new photocrosslinkable polycaprolactone based ink for three dimensional inkjet printing (2016)
Journal Article
He, Y., Tuck, C., Prina, E., Kilsby, S., Christie, S. D., Edmondson, S., …Wildman, R. D. (2017). A new photocrosslinkable polycaprolactone based ink for three dimensional inkjet printing. Journal of Biomedical Materials Research Part B: Applied Biomaterials, 105(6), 1645-1657. https://doi.org/10.1002/jbm.b.33699

A new type of photocrosslinkable polycaprolactone (PCL)-based ink that is suitable for three-dimensional (3D) inkjet printing has been developed. Photocrosslinkable PCL dimethylacrylate was synthesized and mixed with poly(ethylene glycol) diacrylate... Read More about A new photocrosslinkable polycaprolactone based ink for three dimensional inkjet printing.

Surface microstructuring to modify wettability for 3D printing of nano-filled inks (2016)
Journal Article
Vafaei, S., Tuck, C., Ashcroft, I., & Wildman, R. D. (2016). Surface microstructuring to modify wettability for 3D printing of nano-filled inks. Chemical Engineering Research and Design, 109, https://doi.org/10.1016/j.cherd.2016.02.004

This paper investigates the effect of surface wettability on the cross-sectional profiles of printed nanofluid inks which can have a significant role on conductivity of printed lines that are used in the production of printed electronics. Glass subst... Read More about Surface microstructuring to modify wettability for 3D printing of nano-filled inks.

Shape complexity and process energy consumption in electron beam melting: a case of something for nothing in additive manufacturing? (2016)
Journal Article
Baumers, M., Tuck, C., Wildman, R. D., Ashcroft, I., & Hague, R. J. (in press). Shape complexity and process energy consumption in electron beam melting: a case of something for nothing in additive manufacturing?. Journal of Industrial Ecology, https://doi.org/10.1111/jiec.12397

Additive manufacturing (AM) technology is capable of building up component geometry in a layer-by-layer process, entirely without tools, molds, or dies. One advantage of the approach is that it is capable of efficiently creating complex product geome... Read More about Shape complexity and process energy consumption in electron beam melting: a case of something for nothing in additive manufacturing?.

Three dimensional ink-jet printing of biomaterials using ionic liquids and co-solvents (2016)
Journal Article
Gunasekera, D. H., Kuek, S., Hasanaj, D., He, Y., Tuck, C., Croft, A. K., & Wildman, R. D. (2016). Three dimensional ink-jet printing of biomaterials using ionic liquids and co-solvents. Faraday Discussions, 190, 509-523. https://doi.org/10.1039/C5FD00219B

1-Ethyl-3-methylimidazolium acetate ([C2C1Im][OAc]) and 1-butyl-3-methylimidazolium acetate ([C4C1Im][OAc]) have been used as solvents for the dissolution and ink-jet printing of cellulose from 1.0 to 4.8 wt%, mixed with the co-solvents 1-butanol and... Read More about Three dimensional ink-jet printing of biomaterials using ionic liquids and co-solvents.

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography (2016)
Journal Article
Maskery, I., Aboulkhair, N., Corfield, M., Tuck, C., Clare, A., Leach, R. K., …Hague, R. J. (2016). Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography. Materials Characterization, 111, https://doi.org/10.1016/j.matchar.2015.12.001

We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The spe... Read More about Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomography.

An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials (2015)
Journal Article
Chen, X., Ashcroft, I., Wildman, R. D., & Tuck, C. (2015). An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 471(2183), Article 20150477. https://doi.org/10.1098/rspa.2015.0477

A method using experimental nanoindentation and inverse finite-element analysis (FEA) has been developed that enables the spatial variation of material constitutive properties to be accurately determined. The method was used to measure property varia... Read More about An inverse method for determining the spatially resolved properties of viscoelastic–viscoplastic three-dimensional printed materials.

A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V (2015)
Journal Article
Hague, R., Tuck, C., Simonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., …Hague, R. J. (2015). A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V. Metallurgical and Materials Transactions A, 46(9), 3842-3851. https://doi.org/10.1007/s11661-015-2882-8

The creation of an object by selective laser melting (SLM) occurs by melting contiguous areas of a powder bed according to a corresponding digital model. It is therefore clear that the success of this metal Additive Manufacturing (AM) technology reli... Read More about A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V.

Aging behavior of thermoplastic elastomers in the laser sintering process (2014)
Journal Article
Ziegelmeier, S., Wöllecke, F., Tuck, C. J., Goodridge, R. D., & Hague, R. J. (2014). Aging behavior of thermoplastic elastomers in the laser sintering process. Journal of Materials Research, 29(17), 1841-1851. https://doi.org/10.1557/jmr.2014.172

It is known that polymers used in laser sintering (LS) change their intrinsic properties due to processing conditions that are close to the crystalline melting temperature. This paper evaluates the aging behavior of a thermoplastic polyurethane powde... Read More about Aging behavior of thermoplastic elastomers in the laser sintering process.