Skip to main content

Research Repository

Advanced Search

Outputs (85)

An Unbalanced Capacitor Voltage Buck Converter With Wide Soft Switching Range (2023)
Journal Article
Chen, Q., Klumpner, C., & Ahmed, M. R. (2023). An Unbalanced Capacitor Voltage Buck Converter With Wide Soft Switching Range. IEEE Transactions on Industrial Electronics, https://doi.org/10.1109/tie.2023.3314856

DC–DC converters using soft switching technology have gained popularity in several industrial applications. Nevertheless, a wider soft switching range and a simpler structure are the holy grail for these converters. In this article, an innovative unb... Read More about An Unbalanced Capacitor Voltage Buck Converter With Wide Soft Switching Range.

An Optimisation Tool for Hybrid-Electric Aircraft Propulsion Systems (2023)
Conference Proceeding
Walmsley, R., Ahmed, R., Klumpner, C., & Saleh, B. M. (2023). An Optimisation Tool for Hybrid-Electric Aircraft Propulsion Systems. In 2023 IEEE International Electric Machines & Drives Conference (IEMDC). https://doi.org/10.1109/iemdc55163.2023.10238919

The requirement for reductions in CO 2 , NO X and noise emissions from aviation have come under great assiduity. The use of electric and hybrid-electric propulsion systems within aircraft offer potential performance and efficiency improvements, throu... Read More about An Optimisation Tool for Hybrid-Electric Aircraft Propulsion Systems.

Sliding Mode Input Current Control of the Synchronous DC-DC Buck Converter for Electro-Mechanical Actuator Emulation in More Electric Aircrafts (2022)
Journal Article
Salimi, M., Klumpner, C., & Bozhko, S. (2022). Sliding Mode Input Current Control of the Synchronous DC-DC Buck Converter for Electro-Mechanical Actuator Emulation in More Electric Aircrafts. Energies, 15(24), Article 9628. https://doi.org/10.3390/en15249628

The main challenges of the input current control in synchronous DC-DC buck converters are the nonlinear model of the system, changes of the operating point in a wide range, and the need to use an input LC filter for current smoothing, which may resul... Read More about Sliding Mode Input Current Control of the Synchronous DC-DC Buck Converter for Electro-Mechanical Actuator Emulation in More Electric Aircrafts.

Analysis of Using a Thermoelectric Module for Power Electronics Cooling (2022)
Conference Proceeding
Abubakar, A., Klumpner, C., & Wheeler, P. (2022). Analysis of Using a Thermoelectric Module for Power Electronics Cooling. In 2022 IEEE 1st Industrial Electronics Society Annual On-Line Conference (ONCON) (909-914). https://doi.org/10.1109/oncon56984.2022.10126992

This paper aims to develop a PLECS equivalent circuit of a thermoelectric module to be used in power electronics cooling applications. The proposed model is built using elements from the PLECS thermal model block-set. To test this, a resistive c dev... Read More about Analysis of Using a Thermoelectric Module for Power Electronics Cooling.

A Novel Multiport DC-DC Converter for Enhancing the Design and Performance of Battery–Supercapacitor Hybrid Energy Storage Systems for Unmanned Aerial Vehicles (2022)
Journal Article
Fares, A. M., Klumpner, C., & Sumner, M. (2022). A Novel Multiport DC-DC Converter for Enhancing the Design and Performance of Battery–Supercapacitor Hybrid Energy Storage Systems for Unmanned Aerial Vehicles. Applied Sciences, 12(6), Article 2767. https://doi.org/10.3390/app12062767

This paper proposes an integrated multiport non-isolated DC–DC converter system for integrating battery–supercapacitor hybrid energy storage with photovoltaics for solar-powered unmanned aerial vehicles applications. Compared to the traditional topol... Read More about A Novel Multiport DC-DC Converter for Enhancing the Design and Performance of Battery–Supercapacitor Hybrid Energy Storage Systems for Unmanned Aerial Vehicles.

Development of a smart supercapacitor energy storage system for aircraft electric power systems (2021)
Journal Article
Fares, A. M., Kippke, M., Rashed, M., Klumpner, C., & Bozhko, S. (2021). Development of a smart supercapacitor energy storage system for aircraft electric power systems. Energies, 14(23), Article 8056. https://doi.org/10.3390/en14238056

This paper presents the development of a supercapacitor energy storage system (ESS) aimed to minimize weight, which is very important for aerospace applications, whilst integrating smart functionalities like voltage monitoring, equalization, and over... Read More about Development of a smart supercapacitor energy storage system for aircraft electric power systems.

Modeling and experimental evaluation of z-source modular multilevel converter using reduced inserted cells technique (2021)
Journal Article
Khera, F. A., Klumpner, C., & Wheeler, P. (2021). Modeling and experimental evaluation of z-source modular multilevel converter using reduced inserted cells technique. IEEE Access, 9, 133091-133101. https://doi.org/10.1109/ACCESS.2021.3115634

The integration of a Z-source network with a modular multilevel converter (MMC) to provide voltage step-up function is proposed in this paper. The proposed Z-source modular multilevel converter (ZS-MMC) uses a Z-source network connected between the D... Read More about Modeling and experimental evaluation of z-source modular multilevel converter using reduced inserted cells technique.

Comparison of Frequency Transform Methods for Condition Monitoring of a DC-Link Capacitor (2021)
Conference Proceeding
Raqib, A., Jahanger, H., Sumner, M., Cox, T., Klumpner, C., Agha, I., …Lonsdale, P. (2021). Comparison of Frequency Transform Methods for Condition Monitoring of a DC-Link Capacitor. In 10th International Conference on Power Electronics, Machines and Drives (PEMD 2020) (621 – 626). https://doi.org/10.1049/icp.2021.1169

Electrolytic capacitors continue to be used for the DC-link in motor drive systems due to their high specific capacitance. The degradation of electrolytic capacitors can lead to increased equivalent series resistances (ESR) and reduction in capacitan... Read More about Comparison of Frequency Transform Methods for Condition Monitoring of a DC-Link Capacitor.

Trade-off Analysis of Energy Storage Systems for Helicopter Landing Gear Electromechanical Actuator (2021)
Conference Proceeding
Lukic, M., Giangrande, P., Klumpner, C., & Galea, M. (2021). Trade-off Analysis of Energy Storage Systems for Helicopter Landing Gear Electromechanical Actuator. . https://doi.org/10.1109/ISIE45552.2021.9576403

The aerospace industry is rapidly changing towards more electric aircraft initiative, trying to alleviate pollution problems and obey the authority bodies' strict rules. Not only should aircraft comply with this initiative but also helicopters (i.e.,... Read More about Trade-off Analysis of Energy Storage Systems for Helicopter Landing Gear Electromechanical Actuator.

Experimental evaluation of an energy storage system for medium voltage distribution grids enabling solid?state substation functionality (2021)
Journal Article
Klumpner, C., Rashed, M., De, D., Patel, C., & Asher, G. (2021). Experimental evaluation of an energy storage system for medium voltage distribution grids enabling solid?state substation functionality. IET Smart Grid, 4(2), 190-201. https://doi.org/10.1049/stg2.12019

"Smart grids" is a new concept of managing the power transfer in modern grids that will rely not only on the on-line processing of a variety of consumption and generation power data but will also need new hardware to facilitate a flexible and efficie... Read More about Experimental evaluation of an energy storage system for medium voltage distribution grids enabling solid?state substation functionality.

Analysing the converter requirements for a dual-fed induction machine based flywheel energy storage system (2020)
Presentation / Conference
Klumpner, C. (2020, December). Analysing the converter requirements for a dual-fed induction machine based flywheel energy storage system. Paper presented at 10th International Conference on Power Electronics, Machines and Drives (PEMD 2020), Online

The Dual-fed Induction Machine was used very successfully in wind generators as it allowed full control of the power captured from the wind within a wide relevant rotational speed range around the synchronous speed needing only a low power rated roto... Read More about Analysing the converter requirements for a dual-fed induction machine based flywheel energy storage system.

Quasi Z-Source Hybrid Modular Multilevel Converter Controlled By Reduced Inserted Cells Modulation Technique For Medium Voltage Applications (2020)
Presentation / Conference
Khera, F., Klumpner, C., & Wheeler, P. (2020, December). Quasi Z-Source Hybrid Modular Multilevel Converter Controlled By Reduced Inserted Cells Modulation Technique For Medium Voltage Applications. Paper presented at 10th International Conference on Power Electronics, Machines and Drives (PEMD 2020), Online

This paper presents a novel quasi Z-source Hybrid modular multilevel converter (qZS-HMMC) for medium voltage applications where the “hybrid” concept refers to the implementation of the MMC strings that consist of a mixture of half bridge sub-modules... Read More about Quasi Z-Source Hybrid Modular Multilevel Converter Controlled By Reduced Inserted Cells Modulation Technique For Medium Voltage Applications.

Evaluation of inverter topologies for high power medium voltage aircraft applications (2020)
Presentation / Conference
Klumpner, C., & Khera, F. (2020, December). Evaluation of inverter topologies for high power medium voltage aircraft applications. Paper presented at 10th International Conference on Power Electronics, Machines and Drives (PEMD 2020), Online

Future generation more electric aircrafts will require significantly larger power do be generated on board and for this reason, being able to identify which high power/medium voltage AC/DC power converter topologies would suit the best,is important.... Read More about Evaluation of inverter topologies for high power medium voltage aircraft applications.

Novel Parameter Identification Method for Lithium-Ion Batteries Based on Curve Fitting (2020)
Conference Proceeding
Lukic, M., Giangrande, P., Klumpner, C., & Galea, M. (2020). Novel Parameter Identification Method for Lithium-Ion Batteries Based on Curve Fitting. In 2020 IEEE Vehicle Power and Propulsion Conference (VPPC). https://doi.org/10.1109/vppc49601.2020.9330955

This paper describes a new curve-fitting lithium-ion battery parameter identification method for equivalent circuit models. The current pulse/relaxation test is carried out and the corresponding terminal voltage is used for extracting the battery mod... Read More about Novel Parameter Identification Method for Lithium-Ion Batteries Based on Curve Fitting.

Energy Storage System Selection for Optimal Fuel Consumption of Aircraft Hybrid Electric Taxiing Systems (2020)
Journal Article
Recalde, A., Lukic, M., Hebala, A., Giangrande, P., Klumpner, C., Nuzzo, S., …Galea, M. (2021). Energy Storage System Selection for Optimal Fuel Consumption of Aircraft Hybrid Electric Taxiing Systems. IEEE Transactions on Transportation Electrification, 7(3), 1870-1887. https://doi.org/10.1109/TTE.2020.3039759

IEEE Aircraft taxiing is conventionally performed using the main engines’ inefficient idle thrust. Therefore, in line with greener aviation, the electrification of taxiing is the most viable option to reduce emissions, noise, and fossil fuel consumpt... Read More about Energy Storage System Selection for Optimal Fuel Consumption of Aircraft Hybrid Electric Taxiing Systems.

Integrating a Single Z-Source Network with a Modular Multilevel Converter for Voltage Boosting (2019)
Conference Proceeding
Khera, F. A., Wheeler, P. W., & Klumpner, C. (2019). Integrating a Single Z-Source Network with a Modular Multilevel Converter for Voltage Boosting

This paper proposes the integration of a Z-source network with the modular multilevel converter (MMC) to add voltage boosting capability to a voltage step down converter. To limit the increase in complexity, the proposed Z-source modular multilevel c... Read More about Integrating a Single Z-Source Network with a Modular Multilevel Converter for Voltage Boosting.

Experimental Validation of a quasi Z-Source Modular Multilevel Converter with DC Fault Blocking Capability (2019)
Journal Article
Khera, F., Klumpner, C., & Wheeler, P. (2021). Experimental Validation of a quasi Z-Source Modular Multilevel Converter with DC Fault Blocking Capability. IEEE Journal of Emerging and Selected Topics in Power Electronics, 9(2), 1951-1965. https://doi.org/10.1109/jestpe.2019.2955859

This paper considers the design methodology and the modulation of the quasi Z-source modular multilevel converter (qZS-MMC) with half bridge sub-modules and evaluates its performance in voltage boosting mode for medium voltage applications. The qZS-M... Read More about Experimental Validation of a quasi Z-Source Modular Multilevel Converter with DC Fault Blocking Capability.

Analysis of Energy Storage System Requirements for Aircraft Electric Taxiing Operations (2019)
Conference Proceeding
Lukic, M., Giangrande, P., Klumpner, C., & Galea, M. (2019). Analysis of Energy Storage System Requirements for Aircraft Electric Taxiing Operations. . https://doi.org/10.1109/IECON.2019.8926797

This paper focuses on evaluating the energy and power requirements of a specific aircraft on-board electric taxiing (ET) system. The developed model of the investigated system is used to determine the requisites for a typical taxiing profile mission... Read More about Analysis of Energy Storage System Requirements for Aircraft Electric Taxiing Operations.

An Exploration of Design Options for Integrated Residential PV-ESS (2019)
Conference Proceeding
Panagiotou, K., Klumpner, C., Sumner, M., & Georghiou, G. E. (2019). An Exploration of Design Options for Integrated Residential PV-ESS. In Proceedings: IECON 2019 - 45th Annual Conference of the IEEE Industrial Electronics Society (4721-4726). https://doi.org/10.1109/IECON.2019.8927217

The behind-the-meter integration of the distributed energy sources and the energy storage systems (ESSs) presents one of the key solutions for the 21st century energy and power challenges. A comprehensive design and development procedure, which integ... Read More about An Exploration of Design Options for Integrated Residential PV-ESS.

A Novel Modular Multiport Converter for Enhancing the Performance of Photovoltaic-Battery Based Power Systems (2019)
Journal Article
Fares, A. M., Klumpner, C., & Sumner, M. (2019). A Novel Modular Multiport Converter for Enhancing the Performance of Photovoltaic-Battery Based Power Systems. Applied Sciences, 9(19), https://doi.org/10.3390/app9193948

This paper introduces a novel multiport power converter with modular architecture for photovoltaic (PV)-battery based power systems. Compared to conventional centralized multiport converters, the proposed converter significantly improves the utilizat... Read More about A Novel Modular Multiport Converter for Enhancing the Performance of Photovoltaic-Battery Based Power Systems.

Modelling and Analysis of an Aircraft On-board Electric Taxiing System (2019)
Conference Proceeding
Lukic, M., Giangrande, P., Klumpner, C., & Galea, M. (2019). Modelling and Analysis of an Aircraft On-board Electric Taxiing System. In Proceedings of 2019 22nd International Conference on Electrical Machines and Systems (ICEMS) (1-6). https://doi.org/10.1109/ICEMS.2019.8921709

This paper presents a model that enables analysis and design validation of an aircraft on-board electric taxiing system. A detailed model, which includes power electronics, electrical machine and mechanical drivetrain, is first developed and discusse... Read More about Modelling and Analysis of an Aircraft On-board Electric Taxiing System.

Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs (2019)
Journal Article
Fares, A. M., Klumpner, C., & Sumner, M. (2019). Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs. Journal of Engineering, 2019(17), 3862-3866. https://doi.org/10.1049/joe.2018.8228

The overall performance of battery packs may be affected by imbalances between the series connected cells which is more likely in packs with high number of cells needed to provide a high voltage as needed for example in electric vehicles. In this cas... Read More about Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs.

Design and evaluation of an energy storage system for helicopters (2019)
Journal Article
Klumpner, C., & Rashed, M. (2019). Design and evaluation of an energy storage system for helicopters. Journal of Engineering, 2019(17), 3665-3670. https://doi.org/10.1049/joe.2018.8231

This paper presents the design and evaluation of an energy storage system (ESS) for helicopters with the aim to recover the kinetic energy in the rotor available after landing and to be able to control the 270 V DC bus voltage during load disturbance... Read More about Design and evaluation of an energy storage system for helicopters.

Sizing guidelines for grid-connected decentralised energy storage systems: single house application (2019)
Journal Article
Panagiotou, K., Klumpner, C., & Sumner, M. (2019). Sizing guidelines for grid-connected decentralised energy storage systems: single house application. Journal of Engineering, 2019(17), 3802-3806. https://doi.org/10.1049/joe.2018.8155

Nowadays, the existing hierarchical, centrally controlled power grid faces new challenges due to the increase penetration of renewable sources, the need of implementing demand-side management and the 2020 and 2050 environmental targets. A promising c... Read More about Sizing guidelines for grid-connected decentralised energy storage systems: single house application.

New modulation scheme for bidirectional qZS modular multi-level converters (2019)
Journal Article
Khera, F. A., Klumpner, C., & Wheeler, P. W. (2019). New modulation scheme for bidirectional qZS modular multi-level converters. Journal of Engineering, 2019(17), 3836-3841. https://doi.org/10.1049/joe.2018.8020

This study proposes a dedicated modulation scheme for a bidirectional quasi-Z-source (qZS) modular multi-level converter. The operation principle and a suitable pulse-width modulation method are proposed. The relation between the modulation index and... Read More about New modulation scheme for bidirectional qZS modular multi-level converters.

Design Considerations to Optimise Supercapacitor-based Energy Storage Systems for Aerospace Applications (2018)
Conference Proceeding
Fares, A., Klumpner, C., & Rashed, M. (2018). Design Considerations to Optimise Supercapacitor-based Energy Storage Systems for Aerospace Applications. In 2018 IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC) (1-8). https://doi.org/10.1109/ESARS-ITEC.2018.8607796

© 2018 IEEE. This paper investigates the design optimization of a supercapacitor-based energy storage system for aerospace applications which may be needed to complement the operation of a high power pulsed load such as electromechanical actuators ha... Read More about Design Considerations to Optimise Supercapacitor-based Energy Storage Systems for Aerospace Applications.

Power Density Optimization of a DC/DC Converter for an Aircraft Supercapacitors Energy Storage (2018)
Conference Proceeding
Fritz, N., Rashed, M., & Klumpner, C. (2018). Power Density Optimization of a DC/DC Converter for an Aircraft Supercapacitors Energy Storage. In 2018 IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC) (1-9). https://doi.org/10.1109/ESARS-ITEC.2018.8607774

This paper presents a computationally efficient design algorithm for a DC/DC converter, optimized for power density. Interleaving and series-connecting of several converter cells is included in the analysis. The choice of the converter design paramet... Read More about Power Density Optimization of a DC/DC Converter for an Aircraft Supercapacitors Energy Storage.

State of the Art of Electric Taxiing Systems (2018)
Conference Proceeding
Lukic, M., Hebala, A., Giangrande, P., Klumpner, C., Nuzzo, S., Chen, G., …Galea, M. (2018). State of the Art of Electric Taxiing Systems. In Proceedings - 2018 IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC) (1-6). https://doi.org/10.1109/ESARS-ITEC.2018.8607786

The aviation industry represents an ever-expanding economy and the aircraft market forecast reveals an optimistic growth for the coming decades. New requirements and guidelines call for a more efficient, reliable, and environment friendly aircraft op... Read More about State of the Art of Electric Taxiing Systems.

Design and Evaluation of a Power Converter for an Energy Storage System for Aircrafts (2018)
Conference Proceeding
Klumpner, C., & Rashed, M. (2018). Design and Evaluation of a Power Converter for an Energy Storage System for Aircrafts. In Proceedings - 2018 IEEE International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles & International Transportation Electrification Conference (ESARS-ITEC) (1-8). https://doi.org/10.1109/ESARS-ITEC.2018.8607274

This paper presents the design and evaluation of a power converter to be used in an energy storage system for aircrafts that is be able to control the 270V dc bus voltage during large load disturbances and regeneration. A study is conducted in order... Read More about Design and Evaluation of a Power Converter for an Energy Storage System for Aircrafts.

A comparison of modulation techniques for three-phase quasi Z-source modular multilevel converter able to provide DC-link fault blocking capability (2018)
Presentation / Conference
Khera, F. A., Klumpner, C., & Wheeler, P. W. (2018, September). A comparison of modulation techniques for three-phase quasi Z-source modular multilevel converter able to provide DC-link fault blocking capability. Paper presented at EPE'18 ECCE Europe - 20th European Conference on Power Electronics and Applications

Future transmission and distribution grids will use power converters to enable interface with HVDC systems and the Modular Multilevel Converter (MMC) is a topology that is already employed in commercial systems. The MMC converter inherent the benefit... Read More about A comparison of modulation techniques for three-phase quasi Z-source modular multilevel converter able to provide DC-link fault blocking capability.

Energy harvesting utilizing reciprocating flow-induced torsional vibration on a T-shaped cantilever beam (2018)
Journal Article
Zhang, G., Klumpner, C., & Lin, Y. (2018). Energy harvesting utilizing reciprocating flow-induced torsional vibration on a T-shaped cantilever beam. Smart Materials and Structures, https://doi.org/10.1088/1361-665x/aadb6d

This paper proposes a T-shaped cantilever energy harvester powered by flow-induced torsional vibration. To collect and convert the mechanical (kinetic) energy into electric power, a pair of symmetrical acrylic cylindrical bluff bodies were installed... Read More about Energy harvesting utilizing reciprocating flow-induced torsional vibration on a T-shaped cantilever beam.

New modulation scheme for bidirectional quasi z-source modular multilevel converters (2018)
Conference Proceeding
Khera, F., Klumpner, C., & Wheeler, P. (2018). New modulation scheme for bidirectional quasi z-source modular multilevel converters.

This paper proposes a dedicated modulation scheme for a bidirectional quasi Z-source modular multilevel converter (BqZS-MMC). The operation principle and a suitable PWM method are proposed. The relation between the modulation index and shoot-through... Read More about New modulation scheme for bidirectional quasi z-source modular multilevel converters.

Sizing guidelines for grid-connected decentralised energy storage systems: single house application (2018)
Conference Proceeding
Panagiotou, K., Klumpner, C., & Sumner, M. (2018). Sizing guidelines for grid-connected decentralised energy storage systems: single house application.

Nowadays, the existing hierarchical, centrally controlled power grid faces new challenges due to the increase penetration of renewable sources, the need of implementing demand side management and the 2020 and 2050 environmental targets. A promising c... Read More about Sizing guidelines for grid-connected decentralised energy storage systems: single house application.

Design and evaluation of an energy storage system for helicopters (2018)
Conference Proceeding
Klumpner, C., & Rashed, M. (2018). Design and evaluation of an energy storage system for helicopters.

This paper presents the design and evaluation of an energy storage system (ESS) for helicopters with the aim to recover the kinetic energy in the rotor available after landing and to be able to control the 270V dc bus voltage during load disturbances... Read More about Design and evaluation of an energy storage system for helicopters.

Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs (2018)
Conference Proceeding
Fares, A., Klumpner, C., & Sumner, M. (2018). Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs.

The overall performance of battery packs may be affected by imbalances between the series connected cells which is more likely in packs with high number of cells needed to provide a high voltage as needed for example in electric vehicles. In this cas... Read More about Optimising the structure of a cascaded modular battery system for enhancing the performance of battery packs.

Operation principles of quasi Z-source modular multilevel converters (2018)
Conference Proceeding
Khera, F. A., Klumpner, C., & Wheeler, P. W. (2018). Operation principles of quasi Z-source modular multilevel converters. In Proceedings 2017 IEEE Southern Power Electronics Conference (SPEC) (1-6). https://doi.org/10.1109/SPEC.2017.8333617

This paper proposes the integration of a quasi Z-source network with a modular multilevel converter (MMC) to provide voltage boost capability. The proposed quasi-Z-source MMC uses two symmetrical networks of inductors and capacitors connected between... Read More about Operation principles of quasi Z-source modular multilevel converters.

Design recommendations for energy systems: a UK energy community study (2017)
Conference Proceeding
Panagiotou, K., Klumpner, C., Sumner, M., & Wheeler, P. (in press). Design recommendations for energy systems: a UK energy community study.

One of the key elements towards a decentralised energy sector is the consumers’ choice and participation, as the concept of energy prosumer is gaining more and more ground and energy community projects are spouting across UK. In order for the upcomin... Read More about Design recommendations for energy systems: a UK energy community study.

Investigating the benefits and limitations of cascaded converter topologies used in modular battery systems (2017)
Conference Proceeding
Fares, A., Klumpner, C., & Sumner, M. (2017). Investigating the benefits and limitations of cascaded converter topologies used in modular battery systems. In 2017 IEEE International Symposium on Industrial Electronics (ISIE) (2123-2130). https://doi.org/10.1109/ISIE.2017.8001586

The Performance of battery packs is highly affected by imbalances between the series connected cells that provide the required string voltage. A modular battery implementation based on cascaded converters can have advantages over traditional centrali... Read More about Investigating the benefits and limitations of cascaded converter topologies used in modular battery systems.

Being a member of an energy community: Assessing the financial benefits for end-users and management authority (2017)
Conference Proceeding
Panagiotou, K., Klumpner, C., & Sumner, M. (2017). Being a member of an energy community: Assessing the financial benefits for end-users and management authority. In 2017 IEEE 26th International Symposium on Industrial Electronics (ISIE) (957-963). https://doi.org/10.1109/ISIE.2017.8001375

Since 2011, in the context of sustainable development, UK government has been encouraging individuals to work as groups, and now, more than 5,000 community led projects are sprouted across the country, since more than 50% of the UK citizens had expre... Read More about Being a member of an energy community: Assessing the financial benefits for end-users and management authority.

A flow-induced structure-based kinetic energy harvester (2017)
Conference Proceeding
Zhang, G., Lin, Y., & Klumpner, C. (2017). A flow-induced structure-based kinetic energy harvester.

In this paper, a strategy utilizing a pair of cylinders which are put on the both sides of the cantilever beam and perpendicular to the water flow direction to harvest the energy is demonstrated. The novel flow induced structure based energy harveste... Read More about A flow-induced structure-based kinetic energy harvester.

Mitigating the effect of series capacitance unbalance on the voltage reduction capability of an auxiliary CSI used as switching ripple active filter (2017)
Conference Proceeding
Papadopoulos, S., Klumpner, C., Rashed, M., & Wheeler, P. (2017). Mitigating the effect of series capacitance unbalance on the voltage reduction capability of an auxiliary CSI used as switching ripple active filter. . https://doi.org/10.1109/ECCE.2016.7855244

The use of series connected capacitors for high voltage applications has been proven to be beneficial for voltage stress reduction across power semiconductors. In a 3-phase grid any asymmetry in the value of the series capacitance may lead to signifi... Read More about Mitigating the effect of series capacitance unbalance on the voltage reduction capability of an auxiliary CSI used as switching ripple active filter.

Experimental validation of the solid state substation with embedded energy storage concept (2016)
Conference Proceeding
Klumpner, C., Rashed, M., De, D., Patel, C., Kulsangcharoen, P., & Asher, G. (2016). Experimental validation of the solid state substation with embedded energy storage concept. In 2016 IEEE Energy Conversion Congress and Exposition (ECCE) - Proceedings (1-8). https://doi.org/10.1109/ECCE.2016.7855100

This paper proposes the concept of integrating the energy storage within a Medium Voltage to Low Voltage solid state substation in order to provide new features compatible with the requirements from future more intelligent grids. The principles for t... Read More about Experimental validation of the solid state substation with embedded energy storage concept.

Performance benchmark of Si IGBTs vs. SiC MOSFETs in small-scale wind energy conversion systems (2016)
Conference Proceeding
Hussein, A., Castellazzi, A., Wheeler, P., & Klumpner, C. (in press). Performance benchmark of Si IGBTs vs. SiC MOSFETs in small-scale wind energy conversion systems.

Modern power electronics devices based on SiC power MOSFETs technology become more demanding in the last few years. They show better performance over Si-IGBTs on renewable energy power conversion systems due to their higher switching frequency, highe... Read More about Performance benchmark of Si IGBTs vs. SiC MOSFETs in small-scale wind energy conversion systems.

Development of a battery energy loss observer based on improved equivalent circuit modelling (2016)
Conference Proceeding
Fares, A., Klumpner, C., & Sumner, M. (2016). Development of a battery energy loss observer based on improved equivalent circuit modelling. . https://doi.org/10.1109/EPE.2016.7695602

This paper proposes a new energy loss observer for batteries that has a good accuracy and low complexity. This observer can provide a support for battery management systems (BMS) in terms of predicting battery energy loss and/or battery internal temp... Read More about Development of a battery energy loss observer based on improved equivalent circuit modelling.

Hybrid inverter arrangements to facilitate reduced switching losses of the main inverter (2016)
Conference Proceeding
Klumpner, C., & Zargar, T. (2016). Hybrid inverter arrangements to facilitate reduced switching losses of the main inverter.

This paper investigates two hybrid inverter topologies consisting of a slow switching DC/AC main voltage source inverter and output series connected low-voltage rated, fast switching auxiliary inverters that may be suitable for medium and high voltag... Read More about Hybrid inverter arrangements to facilitate reduced switching losses of the main inverter.

Experimental validation of a hybrid converter with enhanced switching ripple cancellation (2016)
Journal Article
Papadopoulos, S., Klumpner, C., Rashed, M., & Wheeler, P. (2016). Experimental validation of a hybrid converter with enhanced switching ripple cancellation. IET Power Electronics, 9(12), 2360-2368. https://doi.org/10.1049/iet-pel.2015.0984

This study presents the experimental evaluation of a proposed new three phase hybrid converter topology for medium voltage applications. The topology is based on the interconnection of a low switching frequency voltage source inverter (VSI), rated at... Read More about Experimental validation of a hybrid converter with enhanced switching ripple cancellation.

The effect of including power converter losses when modelling energy storage systems: a UK domestic study (2016)
Conference Proceeding
Panagiotou, K., Klumpner, C., & Sumner, M. (2016). The effect of including power converter losses when modelling energy storage systems: a UK domestic study.

Energy storage systems (ESS) are seen as an increasingly important technology for managing electrical distribution systems, and there is now much research into both the underlying technologies of these systems, and their “optimum” management especial... Read More about The effect of including power converter losses when modelling energy storage systems: a UK domestic study.

Investigations in the Modeling and Control of a Medium-Voltage Hybrid Inverter System That Uses a Low-Voltage/Low-Power Rated Auxiliary Current Source Inverter (2015)
Journal Article
Papadopoulos, S., Rashed, M., Klumpner, C., & Wheeler, P. (2016). Investigations in the Modeling and Control of a Medium-Voltage Hybrid Inverter System That Uses a Low-Voltage/Low-Power Rated Auxiliary Current Source Inverter. IEEE Journal of Emerging and Selected Topics in Power Electronics, 4(1), 126-140. https://doi.org/10.1109/JESTPE.2015.2488631

Hybrid converters consist of a main inverter processing the bulk of the power with poor waveform performance and a fast and versatile auxiliary inverter to correct the distortion. In this paper, the main converter is a medium voltage NPC inverter and... Read More about Investigations in the Modeling and Control of a Medium-Voltage Hybrid Inverter System That Uses a Low-Voltage/Low-Power Rated Auxiliary Current Source Inverter.

Dynamic phasor analysis and design of phase-locked loops for single phase grid connected converters (2015)
Journal Article
Rashed, M., Klumpner, C., & Asher, G. (2015). Dynamic phasor analysis and design of phase-locked loops for single phase grid connected converters. COMPEL: The International Journal for Computation and Mathematics in Electrical and Electronic Engineering, 34(4), https://doi.org/10.1108/COMPEL-04-2014-0090

The purpose of the paper is to introduce the Dynamic Phasor Modelling (DPM) approach for stability investigation and control design of single-phase Phase Locked Loops PLLs. The aim is to identify the system instabilities not predicted using the exist... Read More about Dynamic phasor analysis and design of phase-locked loops for single phase grid connected converters.

Experimental Evaluation and Efficiency Optimisation of a Grid-Connected Converter for Household Energy Storage Applications (2014)
Conference Proceeding
Kulsangcharoen, P., Asher, G., Rashed, M., Klumpner, C., Patel, C., & De, D. (2014). Experimental Evaluation and Efficiency Optimisation of a Grid-Connected Converter for Household Energy Storage Applications. In 7th IET International Conference on Power Electronics, Machines and Drives (PEMD 2014). https://doi.org/10.1049/cp.2014.0454

This paper presents the design and the experimental evaluation of a power converter for energy storage applications suitable for household installation or to facilitate distributed energy storage capability within a local/community low-voltage grid.... Read More about Experimental Evaluation and Efficiency Optimisation of a Grid-Connected Converter for Household Energy Storage Applications.

A hybrid inverter system for medium voltage applications using a low voltage auxiliary CSI (2014)
Conference Proceeding
Papadopoulos, S., Rashed, M., Klumpner, C., & Wheeler, P. (2014). A hybrid inverter system for medium voltage applications using a low voltage auxiliary CSI. In 2014 IEEE Energy Conversion Congress and Exposition (ECCE). https://doi.org/10.1109/ecce.2014.6953779

Hybrid converters consist of a main inverter processing the bulk of the power with poor waveform performance and a fast and versatile auxiliary inverter to correct the distortion. In this paper, the main converter is a medium voltage NPC inverter and... Read More about A hybrid inverter system for medium voltage applications using a low voltage auxiliary CSI.

Assessing the accuracy of loss estimation methods for supercapacitor energy storage devices operating under constant power cycling (2014)
Conference Proceeding
Kulsangcharoen, P., Klumpner, C., Rashed, M., Asher, G., Chen, G. Z., & Norman, S. A. (2014). Assessing the accuracy of loss estimation methods for supercapacitor energy storage devices operating under constant power cycling. In 2014 16th European Conference on Power Electronics and Applications. https://doi.org/10.1109/epe.2014.6911043

This paper assesses different energy loss estimation methods using the supercapacitor model parameters extracted from the electrochemical impedance spectroscopy (EIS). Two energy loss estimation methods are applied to two similar supercapacitors from... Read More about Assessing the accuracy of loss estimation methods for supercapacitor energy storage devices operating under constant power cycling.

A hybrid inverter solution for medium voltage applications using series capacitor and a CSI Active Power Filter (SC-APF) (2014)
Conference Proceeding
Papadopoulos, S., Rashed, M., Klumpner, C., & Wheeler, P. (2014). A hybrid inverter solution for medium voltage applications using series capacitor and a CSI Active Power Filter (SC-APF). In 7th IET International Conference on Power Electronics, Machines and Drives (PEMD 2014). https://doi.org/10.1049/cp.2014.0456

This paper proposes a new hybrid inverter solution for medium/high voltage applications that consists of a slow switching inverter using high voltage or series connected switching devices, fitted with a low kVA rated auxiliary current source inverter... Read More about A hybrid inverter solution for medium voltage applications using series capacitor and a CSI Active Power Filter (SC-APF).

Regenerative multi-source power conversion system (2013)
Conference Proceeding
Klumpner, C. (2013). Regenerative multi-source power conversion system.

This presentation shows the progress made on the REGENSYS JTI-CS-2011-3-GRC-03-011 Clean Sky project as of December 2013.

Comparison of multilevel PWM versus interleaved based sinewave shaping for two-stage current source inverters used in PV applications (2013)
Conference Proceeding
Papadopoulos, S., & Klumpner, C. (2013). Comparison of multilevel PWM versus interleaved based sinewave shaping for two-stage current source inverters used in PV applications. In 2013 15th European Conference on Power Electronics and Applications (EPE). https://doi.org/10.1109/EPE.2013.6634633

This paper investigates the advantages of using interleaved based direct sinusoidal current shaping techniques as alternative to 5-level Pulse Width Modulation (PWM) when used in conjunction to a two stage Current Source Inverter (CSI) in PV applicat... Read More about Comparison of multilevel PWM versus interleaved based sinewave shaping for two-stage current source inverters used in PV applications.

Modelling and control of a multi-stage interleaved DC-DC converter with coupled inductors for super-capacitor energy storage system (2013)
Journal Article
De, D., Klumpner, C., Patel, C., Kulsangcharoen, P., Rashed, M., & Asher, G. (2013). Modelling and control of a multi-stage interleaved DC-DC converter with coupled inductors for super-capacitor energy storage system. IET Power Electronics, 6(7), https://doi.org/10.1049/iet-pel.2012.0529

Interleaved converters with coupled inductors are widely used to share load current in high power applications. It offers high equivalent switching frequency and reduced output current ripples using small size magnetic components. Due to smaller comm... Read More about Modelling and control of a multi-stage interleaved DC-DC converter with coupled inductors for super-capacitor energy storage system.

Evaluation of a digitally controlled power electronic emulator for supercapattery (2012)
Conference Proceeding
Kulsangcharoen, P., Rashed, M., Klumpner, C., De, D., Patel, C., Asher, G., & Chen, G. Z. (2012). Evaluation of a digitally controlled power electronic emulator for supercapattery. In 6th IET International Conference on Power Electronics, Machines and Drives (PEMD 2012). https://doi.org/10.1049/cp.2012.0341

Newly developed electrochemical energy storage devices are typically produced as single/small quantity and small size devices. This makes their evaluation very difficult in high power applications that would require production of much larger size dev... Read More about Evaluation of a digitally controlled power electronic emulator for supercapattery.

Achieving the desired transformer leakage inductance necessary in DC-DC converters for energy storage applications (2012)
Conference Proceeding
De, D., Klumpner, C., Rashed, M., Patel, C., Kulsangcharoen, P., & Asher, G. (2012). Achieving the desired transformer leakage inductance necessary in DC-DC converters for energy storage applications. In 6th IET International Conference on Power Electronics, Machines and Drives (PEMD 2012). https://doi.org/10.1049/cp.2012.0212

This paper presents a cost effective winding design and evaluation of a medium frequency isolation transformer typically used in bidirectional isolated DC/DC converters. Since leakage inductance and winding resistance of a high frequency transformer... Read More about Achieving the desired transformer leakage inductance necessary in DC-DC converters for energy storage applications.

Assessing the benefits of hybrid cycloconverters (2011)
Journal Article
Xu, T., Klumpner, C., & Clare, J. (2011). Assessing the benefits of hybrid cycloconverters. IEEE Transactions on Industrial Electronics, 59(1), https://doi.org/10.1109/TIE.2011.2165194

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first to be used in driving electrical motors with variable speed, but now, due to their inferior performance compared to for... Read More about Assessing the benefits of hybrid cycloconverters.

Characterization of energy storage devices for constant power applications (2010)
Conference Proceeding
Kulsangcharoen, P., Klumpner, C., Rashed, M., & Asher, G. (2010). Characterization of energy storage devices for constant power applications. In IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society. https://doi.org/10.1109/IECON.2010.5675401

In this paper, a few known characterization techniques for supercapacitors have been evaluated with the purpose of being able to predict the roundtrip efficiency of an energy storage system under constant power application. It is found that the user... Read More about Characterization of energy storage devices for constant power applications.

High performance multilevel converter topology for interfacing energy storage systems with medium voltage grids (2010)
Conference Proceeding
Rashed, M., Klumpner, C., & Asher, G. (2010). High performance multilevel converter topology for interfacing energy storage systems with medium voltage grids. In IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society. https://doi.org/10.1109/IECON.2010.5675400

This paper proposes a high performance hybrid cascaded H-Bridge (HB) Multilevel Converter (MLC) with integrated Series Active Power Filter SAPF for interfacing energy storage systems with medium voltage grids. Isolated DC sources comprised of modular... Read More about High performance multilevel converter topology for interfacing energy storage systems with medium voltage grids.

Hybrid cascaded multilevel converter with integrated series Active Power Filter for interfacing energy storage system to medium voltage grid (2010)
Conference Proceeding
Rashed, M., Klumpner, C., & Asher, G. (2010). Hybrid cascaded multilevel converter with integrated series Active Power Filter for interfacing energy storage system to medium voltage grid. In The 2010 International Power Electronics Conference - ECCE ASIA -. https://doi.org/10.1109/IPEC.2010.5543461

This paper presents a new control strategy for a high performance hybrid cascaded H-Bridge HB multilevel converter with integrated series Active Power Filter Stage APFS. Unequal DC voltage sources are used to energise the converter's HBs. This offers... Read More about Hybrid cascaded multilevel converter with integrated series Active Power Filter for interfacing energy storage system to medium voltage grid.

Wind turbine-energy storage control system for delivering constant demand power shared by DFIGs through droop characteristics (2009)
Conference Proceeding
Fazeli, M., Asher, G., Klumpner, C., Bozhko, S., Yao, L., & Bazargan, M. (2009). Wind turbine-energy storage control system for delivering constant demand power shared by DFIGs through droop characteristics. In 2009 13th European Conference on Power Electronics and Applications

This paper investigates embedding Energy Storage (ES) with multiple wind turbines in order to deliver to the grid a smooth and constant power as demanded by the system operator. The demand power is shared by DFIGs proportional to their ratings utiliz... Read More about Wind turbine-energy storage control system for delivering constant demand power shared by DFIGs through droop characteristics.

A cost-effective solution to power the gate drivers of multilevel inverters using the bootstrap power supply technique (2009)
Conference Proceeding
Klumpner, C., & Shattock, N. (2009). A cost-effective solution to power the gate drivers of multilevel inverters using the bootstrap power supply technique. In 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition. https://doi.org/10.1109/APEC.2009.4802910

Multilevel inverters are traditionally seen as a step forward in DC/AC conversion, providing more output voltage levels, better quality of the generated waveform and lower switching losses than the two-level and can process higher voltages with a giv... Read More about A cost-effective solution to power the gate drivers of multilevel inverters using the bootstrap power supply technique.

Experimental evaluation of hybrid cycloconverters (2009)
Conference Proceeding
Klumpner, C., Xu, T., & Clare, J. C. (2009). Experimental evaluation of hybrid cycloconverters. In 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition. https://doi.org/10.1109/APEC.2009.4802737

Power converters consisting of naturally commutated thyristors such as cycloconverters and current source inverters were the first used in driving electrical motors with variable speed but now due to their inferior performance compared to forced comm... Read More about Experimental evaluation of hybrid cycloconverters.

Implementation of a hybrid AC-AC direct power converter with unity voltage transfer (2008)
Journal Article
Wijekoon, T., Klumpner, C., Zanchetta, P., & Wheeler, P. (2008). Implementation of a hybrid AC-AC direct power converter with unity voltage transfer. IEEE Transactions on Power Electronics, 23(4), https://doi.org/10.1109/TPEL.2008.924601

This paper presents a novel hybrid direct power converter (HDPC) which overcomes the two main disadvantages of matrix converters: limited voltage transfer ratio and low immunity to grid disturbance. The proposed converter is formed by integrating a r... Read More about Implementation of a hybrid AC-AC direct power converter with unity voltage transfer.

Hybrid matrix converter topologies: an exploration of benefits (2008)
Conference Proceeding
Klumpner, C., & Pitic, C. (2008). Hybrid matrix converter topologies: an exploration of benefits. In 2008 IEEE Power Electronics Specialists Conference. https://doi.org/10.1109/PESC.2008.4591887

Matrix converters are direct AC/AC power converters that can operate with sinusoidal output/input voltage/currents without the need of passive components to store energy, which means that they are grid friendly and have a great weight/volume reductio... Read More about Hybrid matrix converter topologies: an exploration of benefits.

A new class of hybrid AC/AC direct power converters
Conference Proceeding
Klumpner, C., Wijekoon, T., & Wheeler, P. (in press). A new class of hybrid AC/AC direct power converters. In Fourtieth IAS Annual Meeting. Conference Record of the 2005 Industry Applications Conference, 2005. https://doi.org/10.1109/IAS.2005.1518793

Variable voltage and variable frequency conversion of electrical energy from an AC source to an AC load is done in traditional power converters via a DC-link where an energy storage element (electrolytic capacitors) is situated. Despite its well-know... Read More about A new class of hybrid AC/AC direct power converters.

A hybrid indirect matrix converter immune to unbalanced voltage supply, with reduced switching losses and improved voltage transfer ratio
Conference Proceeding
Klumpner, C. (in press). A hybrid indirect matrix converter immune to unbalanced voltage supply, with reduced switching losses and improved voltage transfer ratio. In Twenty-First Annual IEEE Applied Power Electronics Conference and Exposition, 2006. APEC '06. https://doi.org/10.1109/APEC.2006.1620528

Achieving a compact and efficient design of power electronic converters is not a straightforward procedure: minimizing the size of the filter requires a higher switching frequency that causes additional switching losses that will require a larger hea... Read More about A hybrid indirect matrix converter immune to unbalanced voltage supply, with reduced switching losses and improved voltage transfer ratio.

A new two-stage voltage source inverter with modulated DC-link voltage and reduced switching losses
Conference Proceeding
Klumpner, C. (in press). A new two-stage voltage source inverter with modulated DC-link voltage and reduced switching losses. In IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics. https://doi.org/10.1109/IECON.2006.347904

This paper proposes a new DC/AC power converter topology that is obtained by merging a buck type DC/DC converter and a DC/AC three-phase PWM Voltage Source Inverter (VSI) without the need of the passive components (smoothing inductor and capacitance)... Read More about A new two-stage voltage source inverter with modulated DC-link voltage and reduced switching losses.

A new three-level sparse indirect matrix converter
Conference Proceeding
Klumpner, C., Lee, M. Y., & Wheeler, P. (in press). A new three-level sparse indirect matrix converter. In IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics. https://doi.org/10.1109/IECON.2006.347958

Matrix converters are forced commutated single stage AC/AC direct frequency changers able to achieve sine wave in and out operation by being able to connect any input phase to any output phase via a 3x3 matrix of bi-directional switches. Indirect two... Read More about A new three-level sparse indirect matrix converter.

A new hybrid cycloconverter with smooth output voltage generation capability and accurate control of the circulating current
Conference Proceeding
Klumpner, C., Xu, T., & Clare, J. (in press). A new hybrid cycloconverter with smooth output voltage generation capability and accurate control of the circulating current. In IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics. https://doi.org/10.1109/IECON.2006.347850

Nowadays, power electronic converters based exclusively on IGBTs deliver excellent load side performance up to megawatt powers in the low voltage range (200-690V) and are steadily gaining performance in the medium voltage range as well. However, the... Read More about A new hybrid cycloconverter with smooth output voltage generation capability and accurate control of the circulating current.

A new three-level indirect matrix converter with reduced number of switches
Conference Proceeding
Klumpner, C., Lee, M. Y., Pitic, C., Wheeler, P., & Zanchetta, P. (in press). A new three-level indirect matrix converter with reduced number of switches. In 2007 IEEE Industry Applications Annual Meeting. https://doi.org/10.1109/07IAS.2007.28

Matrix converters are sine wave in/out forced commutated single-stage AC/AC direct frequency changers using a single bi-directional switch to connect any input to any output. Indirect two-stage matrix converters provide similar input and output perfo... Read More about A new three-level indirect matrix converter with reduced number of switches.

A new single-stage current source inverter for photovoltaic and fuel cell applications using reverse blocking IGBTs
Conference Proceeding
Klumpner, C. (in press). A new single-stage current source inverter for photovoltaic and fuel cell applications using reverse blocking IGBTs. In 2007 IEEE Power Electronics Specialists Conference. https://doi.org/10.1109/PESC.2007.4342251

Renewable energy sources such as photovoltaics (PVs) or fuel cells (FCs) are not fitted for direct power grid connection because they deliver DC voltage and current. This is why a power electronic interface is needed, consisting usually of a current-... Read More about A new single-stage current source inverter for photovoltaic and fuel cell applications using reverse blocking IGBTs.

Assessing the benefits of installing energy storage in a household equipped with photovoltaic panels
Conference Proceeding
Klumpner, C., & El Boudali, A. (in press). Assessing the benefits of installing energy storage in a household equipped with photovoltaic panels.

This paper evaluates the technical and financial impact of installing energy storage in a house equipped with Photovoltaic (PV) panels subject to the Feed-In Tariff (FIT). An additional benefit of installing energy storage is the possibility to purch... Read More about Assessing the benefits of installing energy storage in a household equipped with photovoltaic panels.

A power electronic controlled dump load with negligible harmonics for accurate loading used in testing small wind turbines
Conference Proceeding
Klumpner, C., Al, B., & Hann, D. B. (in press). A power electronic controlled dump load with negligible harmonics for accurate loading used in testing small wind turbines. In 2010 IEEE International Symposium on Industrial Electronics. https://doi.org/10.1109/ISIE.2010.5637240

Permanent magnet synchronous generators (PMSG) are at the core of small scale wind power generators manufactured by a wide range of manufacturers in different configurations: vertical or horizontal axis blades, with various geometries and aerodynamic... Read More about A power electronic controlled dump load with negligible harmonics for accurate loading used in testing small wind turbines.

Efficiency evaluation of a novel supercapattery stack with a power electronic interface for energy storage systems
Conference Proceeding
Kulsangcharoen, P., Klumpner, C., Zhou, X., Peng, C., Chen, G. Z., Rashed, M., & Asher, G. (in press). Efficiency evaluation of a novel supercapattery stack with a power electronic interface for energy storage systems.

The increase of renewable energy generation seen as the only way to ensure clean and sustainable development, is under scrutiny due to its intermittent nature and an insufficient development of com-plementary technologies such as electrical energy st... Read More about Efficiency evaluation of a novel supercapattery stack with a power electronic interface for energy storage systems.

A current source inverter with series connected AC capacitors for photovoltaic application with grid fault ride through capability
Conference Proceeding
Photong, C., Klumpner, C., & Wheeler, P. (in press). A current source inverter with series connected AC capacitors for photovoltaic application with grid fault ride through capability. In 2009 35th Annual Conference of IEEE Industrial Electronics. https://doi.org/10.1109/IECON.2009.5414954

The current source inverter (CSI) is preferred to interface a renewable source such photovoltaics (PV) to the AC power grid because it can provide smooth current source in the DC side, which fits to the PV behaviour and also steps-up the voltage from... Read More about A current source inverter with series connected AC capacitors for photovoltaic application with grid fault ride through capability.

Selecting the power electronic interface for a supercapattery based energy storage system
Conference Proceeding
Klumpner, C., Asher, G., & Chen, G. Z. (in press). Selecting the power electronic interface for a supercapattery based energy storage system. In 2009 IEEE Bucharest PowerTech. https://doi.org/10.1109/PTC.2009.5281965

This paper presents the initial investigations in selecting the topology of the power electronic interface for an energy storage system for power levelling applications based on a novel storage device, the supercapattery. The particularities of the s... Read More about Selecting the power electronic interface for a supercapattery based energy storage system.

A more efficient current source inverter with series connected AC capacitors for photovoltaic and fuel cell applications
Conference Proceeding
Klumpner, C., Chonlatee, P., & Wheeler, P. (in press). A more efficient current source inverter with series connected AC capacitors for photovoltaic and fuel cell applications.

Renewable energy sources such as photovoltaics (PVs) or fuel cells (FCs) are not fitted for direct power grid connection because they deliver DC voltage and current. In addition, they also have a high internal resistance/nonlinear V/I dependence, whi... Read More about A more efficient current source inverter with series connected AC capacitors for photovoltaic and fuel cell applications.

A two-stage power converter for welding applications with increased efficiency and reduced filtering
Conference Proceeding
Klumpner, C., & Corbridge, M. (in press). A two-stage power converter for welding applications with increased efficiency and reduced filtering. In 2008 IEEE International Symposium on Industrial Electronics. https://doi.org/10.1109/ISIE.2008.4677248

The power supply technology used in welding applications changed dramatically from manually tap-controlled 50Hz bulky transformers which had large leakage inductance to provide stable arc burn to switch-mode fast controlled highfrequency power electr... Read More about A two-stage power converter for welding applications with increased efficiency and reduced filtering.